VOLCANO INGROUND LED LIGHT Operating Instructions

PRECAUTIONS The VOLCANO series of modular outdoor light with built-in driver is designed to use the latest LED lighting technology. The modular designed casing enables the selection of different light engines and beam angles. The VOLCANO series is available in modular stainless steel casings with PMMA or tempered glass lighting windows. The lighting is available in cool white, warm white, red, green, blue, RGB or RGBW colors with 1, 2 or 3 high-power LEDs. The most advanced engine with built-in microprocessor enables network connection and simple control of complete groups of single-color or...

(1) Engine assembly LED lighting assembly built-in sand-blasted anodized aluminium casing with different lighting color, power and beam options.

(2) Inground beam assembly Sand-blasted stainless steel assembly for direct or reflective spreading of lighting in different angles. The modular INGROUND LED light VOLCANO series consists of the following assemblies: • Engine assembly • Inground beam assembly • Inground niche assembly

The assembling and installation have to be realized by qualified personnel. The VOLCANO has to be assembled and fixed as shown in the drawing below: Insert the connection cable and build-in the Inground niche assembly to the ground. Connect the power supply and control wires Tighten the Engine assembly to the Inground beam assembly Fix the jointed Engine assembly/Inground beam assembly to the fixed Inground niche assembly by using of 3 enclosed screws M4 Note:  Do not overtighten the screws as this can result in inground light damage. Note:  Do not cover the inground light body with any kind...

The power supply has to be connected through the main switch (not included) with correct polarity and protected by a fuse (not included). The power supply voltage range has to be from 10 - 30 Vdc. Note: • The power supply has to be switched off before installation. The light engine has to be connected as described in the table below: For basic control of the light the CONTROL wire has to be connected through the momentary switch (not included) to the GND by using a 2-pole signal cable extension. (not included) For DMX512 control optional LXU01 or LXU03 interface can be connected to the CONTROL...

Dimming When the light is on, press the momentary switch longer until the desired power is achieved. Turning on minimum When the light is off, press the momentary switch longer (e.g. one second or more) until the light is turned on at minimum power. Set default Press the momentary switch for min. 40 seconds or until the light is turned off. DMX512 control The network connection to control the light with the standard DMX512 protocol is enabled by using optional LXU01 or LXU03 interfaces. Multi-color (ENGRGB) model: Control by momentary switch Remote control by momentary switch has to be used to...

DMX512 control The built-in ASTEL protocol enables the network connection to control the lights with the standard DMX512 protocol by using optional LXU01 or LXU03 interfaces. Multi-color (ENGRGBW) model: Control by momentary switch Remote control by momentary switch has to be used to turn-on and turn-off the light and to control the mode of lighting and luminosity. When the light is turned-off the color or mode of lighting can be changed sequentially by pressing the momentary switch for 2 seconds: ENGRGBW Sequence of lighting Custom Color _Full RGB_ _Cool White_ _Bluish White_ _Red_ _Green_ _Blue_...

Engine assembly Power supply Beam angle Optical window Luminous flux Operating temperature Casing Protection Dimensions Weight Inground beam assembly Material Dimensions Weight Stainless steel (SAE316L) with PMMA or tempered glass 0110 x 27 mm (IGBD) 0110 x 28 mm (IGBR) 0.8 kg (IGBD) 0.8 kg (IGBR120) 0.7 kg (IGBR240) 0.6 kg (IGBR360) Inground niche assembly Material Stainless steel (SAE316L) and PMMA Design and specifications subject to change without notice.

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement...

DECLARATION OF CONFORMITY according to IEC Guide 22 and EN 45014 Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. INGROUND LED light VOLCANO series conform to the following Product Specifications: EMC: Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CEmarking accordingly: - the EMC Directive 2004/108/EC - the Low Voltage Directive 2006/95/EC ASTEL d.o.o. Dutovlje...