Catalogs >
ASTEL LIGHTING >
Flood - Path LED Light SIGMA

Flood - Path LED Light SIGMA
16Pages

Catalog excerpts

SIGMA FLOOD-PATH LED LIGHT Operating Instructions

PRECAUTIONS The SIGMA series of modular outdoor light with built-in driver is designed to use the latest LED lighting technology. The modular designed casing enables the selection of different light engines, heights, supports and beams. The SIGMA series is available in modular sand-blasted and anodized aluminium casings with E6C0 finishing. The lighting is available in cool white, warm white, red, green, blue, RGB or RGBW colors with 1, 2or3 high-power LEDs. The most advanced engine with built-in microprocessor enables network connection and simple control of complete groups of single-color...

Open the catalog to page 3

(1) Engine assembly LED lighting assembly built-in sand-blasted anodized aluminium casing with different lighting color, power and beam options.

Open the catalog to page 4

(2) Bezel assembly Sand-blasted anodized aluminium bezel assembly for adapting of the engine assembly.

Open the catalog to page 5

The modular flood-path LED light SIGMA series consists of the following assemblies: • Engine assembly • Bezel assembly • Flood-light support assembly • Tube assembly The assembling and installation have to be realized by qualified personnel. The SIGMA has to be assembled and fixed as shown in the drawing below:

Open the catalog to page 7

a) Insert the connection cable and fix the basic component of the Tube assembly to the prepared flat surface or ground by using of 3 fixing screws M8x60 with wallplugs. b) Push the tube to the basic component of the Tube assembly and fix it with 3 enclosed screws M5 c) Fix the Engine assembly to the Flood-light support assembly with 2 enclosed screws M6 with washers d) Connect the power supply and control wires e) Tighten the jointed Engine assembly/Flood-light support assembly to the fixed Tube assembly f) Tighten the Bezel assembly to the Engine assembly Note: • Do not overtighten the...

Open the catalog to page 8

Synchronization When more than one light is connected to the system the optional Synchronization Unit LSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting. On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode. If the multi-color RGB light is used only with one of the fixed color of lighting the synchronization is not necessary. CONTROLS Single-color warm white (ENGWW), cool white (ENGWW), red (ENGR), blue (ENGB) or green (ENGG) models. Control...

Open the catalog to page 9

Turning on /off Press the momentary switch shortly. Changing the color or mode of lighting When the light is turned-off press the momentary switch for 2 seconds. Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected. Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the...

Open the catalog to page 10

Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected. Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity will increase to the maximum illumination. Set default Press the momentary switch for min. 40 seconds or until the light is turned off. DMX512...

Open the catalog to page 11

Tube assembly Material Anodized aluminium BEZEL code ENGINE code 123 SUPPORT code TUBE code Design and specifications subject to change without notice.

Open the catalog to page 12

Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Flood-Path LED light SIGMA series conform to the following Product Specifications: EMC: EN 55015:2006 + A1:2007 Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CE-marking accordingly: - the EMC Directive 2004/108/EC - the Low Voltage Directive 2006/95/EC ASTEL d.o.o. Dutovlje 138 6221...

Open the catalog to page 14

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written...

Open the catalog to page 15