Flood LED Light SOLEA
16Pages

SOLEA FLOOD LED LIGHT Operating Instructions

PRECAUTIONS The SOLEA series of modular outdoor light with built-in driver is designed to use the latest LED lighting technology. The modular designed casing enables the selection of different light engines and brackets. The SOLEA series is available in modular sand-blasted and anodized aluminium casings with E6C0 finishing. The lighting is available in cool white, warm white, red, green, blue, RGB or RGBW colors with 1, 2or3 high-power LEDs. The most advanced engine with built-in microprocessor enables network connection and simple control of complete groups of single-color or multi-color...

(1) Engine assembly LED lighting assembly built-in sand-blasted anodized aluminium casing with different lighting color, power and beam options. (2) Bezel assembly Sand-blasted anodized aluminium bezel assembly for adapting of the engine assembly.

(3) Flood-light bracket assembly Sand-blasted anodized aluminium assembly for engine installations which enable different fixing of the light. The modular FLOOD LED light SOLEA series consists of the following assemblies: • Engine assembly • Bezel assembly • Flood-light bracket assembly The assembling and installation have to be realized by qualified personnel. The SOLEA has to be assembled and fixed as shown in the drawing below:

a) Fix the basic component of the high-end Flood-light bracket assembly or the economy Floodlight bracket assembly to the wall by using of 3(2) fixing screws 6.3x50 with wallplugs. b) Connect the power supply and control wires c) Fix the moving head of the high-end Flood-light bracket assembly with 4 enclosed screws M4 d) Fix the Engine assembly to the Flood-light bracket assembly with 2 enclosed screws M6 with washers e) Tighten the Bezel assembly to the Engine assembly Note: • Do not overtighten the screws and threads as this can result in flood light damage. Note: • Do not cover the...

Synchronization When more than one light is connected to the system the optional Synchronization Unit LSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting. On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode. If the multi-color RGB light is used only with one of the fixed color of lighting the synchronization is not necessary. Single-color warm white (ENGWW), cool white (ENGWW), red (ENGR), blue (ENGB) or green (ENGG) models. Control by...

Turning on /off Press the momentary switch shortly. Changing the color or mode of lighting When the light is turned-off press the momentary switch for 2 seconds. Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected. Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the...

Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected. Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity will increase to the maximum illumination. Set default Press the momentary switch for min. 40 seconds or until the light is turned off. DMX512 control...

Engine assembly Power supply Beam angle Optical window Luminous flux (cool white) Operating temperature Casing Protection Dimensions Weight Bezel assembly Material Dimensions Weight Flood-light bracket assembly Material Dimensions Anodized aluminium 086 x 7 mm (LB86) 0100 x 38 mm (LB100) 0.2 kg (LB86) 0.3 kg (LB100) Anodized aluminium 086 x 65 mm (FLBW) 63 x 62 x 86 mm (FLBS) 63 x 30 x 63 mm (FLBE) 0.5 kg (FLBW) 0.1 kg (FLBS) 0.1 kg (FLBE) BEZEL code ENGINE code 123 BEAM code Design and specifications subject to change without notice. 10

Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. FLOOD LED light SOLEA series conform to the following Product Specifications: EMC: EN 55015:2006 + A1:2007 Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CE-marking accordingly: - the EMC Directive 2004/108/EC - the Low Voltage Directive 2006/95/EC ASTEL d.o.o. Dutovlje 138 6221 Dutovlje Slovenija

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written...