Escenta
3Pages

3.3 Anti-Microbial Preservation Escenta is a water-based decorative wall coating uniquely formulated to create a multi-tone effect, which brings drama and interest to any interior. Escenta is available in a wide range of colours. Test Method Result Anti-Fungal Activity No visible growth Anti-Algal Activity No visible growth Anti-Bacterial - JIS Z 2801 E Coli No bacteria survived > MRSA No bacteria survived Salmonella No bacteria survived A cost effective alternative to decorative paint effect, wall paper and vinyl wall coverings. 3.4 Fire Test Results Օ Provides a seamless, durable, cleanable, hardwearing and low maintenance wall finish. Test Method Result Comments Available in a co-ordinated range of 24 colours. BS476 Part 6&7 Class 0 Escenta System tested Օ Formulated to prevent mould, mildew and bacterial growth. (BaseColor Matt -1 coat, Escenta - 1 coat) Low VOCs & low odour. Օ Coverage rate: approximately 8 -10 m/lt/coat. One 5 lt unit will cover approximately 45 mҲ (450 ft) in 1 coat. > ҕ Drying time: 3 4 hours. For interior use only. > 3.1 Scrub Resistance 5.1 New Surfaces The Escenta system (BaseColor Matt Y2981, Escenta 01) was tested for wet scrub resistance according to ASTM D2486 ֓Standard Test Methods for Scrub Resistance of Wall Paints. ԕ Ensure all surfaces are sound, clean and suitably dry. Dense or highly polished surfaces should be coated with an appropriate primer to promote effective adhesion. Test Method Result Օ Porous surfaces should be primed with a mist coat of BaseColor Matt thinned with up to 20% clean water. ASTM D2486 670 cycles Testing was carried out by an accredited testing laboratory. Leave to dry. 3.2 VOC Testing 5.2 Previously decorated surfaces A sample of Escenta was tested for VOC following procedures outlined in ASTM D3960 ՓStandard Practise for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings and ISO 11890-2 ԓPaints and varnishes. Determination of volatile organic compound (VOC) content. ԕ Ensure all surfaces are sound, clean and suitably dry. Remove any loose or flaking material back to a sound firm edge. Օ Treat any organic growth with a fungicidal wash. Fill any holes, cracks or surface defects. Test Method Result Comments Օ Surfaces that exhibit high sheen levels should be wet abraded to provide a key. ASTM D3960 160 g/lt US EPA requirement (<250g/lt) Wash down sound paintwork with warm water and an appropriate cleaning agent to remove any contaminants. ISO 11890-2 40g/lt EU requirement for Cat A/l (300g/lt) Technical Data Sheet TDS302 Escenta 01, 02, 03 & 04 Page 1 of 3 >

Rinse surfaces with clean water to remove any residues. Օ Spot prime any bare or filled areas with a mist coat of BaseColor Matt or an appropriate primer as necessary. Take the sponge float and stipple/tamp the material directly onto the surface. Օ Constantly rotate the orientation of the float, and always pull off away from the wall surface. Leave to dry. Օ Apply the material sparingly, but make sure that there are no areas of the BaseColor that have been left uncoated. > Work from the top corner of the wall, working progressively down and across the wall in a fan shape rather than in...

Shelf life of Perlata in an unopened container under correct storage condition is 12 months from date of manufacture. > 10.1 Cleaning Surface Dirt and Grime Mix a small quantity of liquid detergent or soap into a bucket of clean water. Work from top to bottom of dirty area using a well-soaked, soft cloth, sponge, very soft bristle brush or low pressure garden mist sprayer. Do not use scouring pads, industrial strength cleaners or solvents, since these may damage the surface finish. Do not allow cleaning solution to dry on the wall. Where possible blot the wall dry with an absorbent towel or...