SEAMLESS SCULPTURAL WALL SURFACE DESIGNS

HOUR CLASS MONROE BARCODE FLOW WAVE JET STREAM Armourcoat Sculptural® is a range of seamless sculptural wall surface designs. Armourcoat Sculptural® walls are constructed from a series of pre-cast panels that are bonded to the substrate. The panel joints are then filled and sanded and a final decoration is applied to the surface. Armourcoat Sculptural® designs are created by combining computer-aided design with traditional hand sculpting to create designs that fit together with total accuracy yet retain the essence of being hand crafted. Some of the designs are based on a single panel that creates...

PANEL MAX PANEL FINISH: SPRAY: RECOMMENDED SCULPTURAL DIMENSIONS DEPTH WEIGHT NUMBER OF PANEL ORIENTATION SPATULATA/ PERLATA/ ORIENTATION RECOMMENDED DESIGN (mm) (mm) (kg/m2) PANEL DESIGNS (Horizontal/Vertical) ARMURALIA PAINT (Horizontal/Vertical) FINISH

PANEL MAX PANEL FINISH: SPRAY: SCULPTURAL DIMENSIONS DEPTH WEIGHT NUMBER OF PANEL ORIENTATION SPATULATA/ PERLATA/ DESIGN (mm) (mm) (kg/m2) PANEL DESIGNS (Horizontal/Vertical) ARMURALIA PAINT ORIENTATION RECOMMENDED (Horizontal/Vertical) FINISH

PANEL MAX PANEL FINISH: SPRAY: SCULPTURAL DIMENSIONS DEPTH WEIGHT NUMBER OF PANEL ORIENTATION SPATULATA/ PERLATA/ DESIGN (mm) (mm) (kg/m2) PANEL DESIGNS (Horizontal/Vertical) ARMURALIA PAINT ORIENTATION RECOMMENDED (Horizontal/Vertical) FINISH

PANEL MAX PANEL FINISH: SPRAY: SCULPTURAL DIMENSIONS DEPTH WEIGHT NUMBER OF PANEL ORIENTATION SPATULATA/ PERLATA/ DESIGN (mm) (mm) (kg/m2) PANEL DESIGNS (Horizontal/Vertical) ARMURALIA PAINT ORIENTATION RECOMMENDED (Horizontal/Vertical) FINISH

Material composition Armourcoat Sculptural® wall panels are made from a high strength fibre reinforced gypsum plaster combined with an inert mineral filler. The filler, a post-consumer recycled material, constitutes up to 30% (depending on design) of the panel's composition. The panels are non- toxic, and contain no VOCs or formaldehyde. Panel dimensions and weight. The panel dimensions vary depending upon the design but most designs are either 1800mm thickness of the panels may vary from 14mm - 25 mm depending upon the depth of the sculpting to the surface. The panels vary in weight depending...

SCULPTURAL DIMENSIONS MAX PANEL FINISH: SPRAY: RECOMMENDED DEPTH WEIGHT NUMBER OF PANEL ORIENTATION SPATULATA/ PERLATA/ ORIENTATION RECOMMENDED (mm) (kg/m2) PANEL DESIGNS (Horizontal/Vertical) ARMURALIA PAINT (Horizontal/Vertical) FINISH Perlata / Paint

Standard Armourcoat Sculptural19 panels are suitable for internal use and areas that are not exposed to the elements or large temperature Wall size We do not recommend installing Armourcoat Sculptural® panels to wall in excess of 10 metres in length or 40m2 in surface area without some form of control joint or expansion gap. In situations where the aesthetics demand long uninterrupted surfaces the control joint can be with a flexible filler or mastic that is close in colour to the rest of the wall. Large walls are subject to a risk of small hairline cracks developing between the panels due to...

Achieving the correct lighting is critical to the success of Armourcoat Sculptural® walls. To get the best results it is important to light the surface to achieve the optimum interplay between highlight and shadow. The walls can either be down lit, up lit or even cross lit for any design that runs vertically. The angle of incidence for the light source to the face of the wall can vary depending upon the effect required, but as a guide we would recommend that the light strikes the wall surface at an angle of between 8-25° with 15-18° being about the optimum. For a 3m high wall you would set the...

^^^^^^^ S U RFACE FINISHES Armourcoat Limited, Morewood Close, Sevenoaks, Kent TN13 2HU, United Kingdom Telephone:+44(0)1732 460668 Fax:+44(0)1732 450930 Email: [email protected] Website: www.armourcoat.com ©2014 Armourcoat Ltd. Armourcoat Sculptural is a product and trademark of Armourcoat Ltd.