Ecoburn (S3) Gas Conventional Flueo
36Pages

ARADA - DEVON - Ecoburn (S3) Gas Conventional Flue Installation, Servicing and User Guide PLEASE RETAIN THIS GUIDE FOR FUTURE REFERENCE For use in GB & IE (United Kingdom and Ireland) SPECIFIC Rev 02 ISSUE DATE : 24/06/2021

Ecoburn (S3) Gas CF Stove Installation and Servicing Ecoburn (S3) Gas Stove Congratulations on the purchase of your new Arada stove! Your stove is built to the highest standard of craftsmanship using the best materials and the most modern equipment available. It is a highly efficient and sophisticated piece of machinery and when properly installed and operated it should provide a lifetime of heating satisfaction. Should you have any questions about your stove which are not covered by this manual, please contact the Arada retailer in your area, call our technical support department on +44...

Ecoburn (S3) Gas CF Stove Installation and Servicing Installation & Service Contents Installation & Service 2 Installation 2.1 Hearth…………………………………………………………….. 2.2 Siting ……………………………………………………………... 2.3 Flue Connection …………………………………………………. 2.4 Ventilation ……………………………………………………….. 2.5 Gas Connection …………………………………………………. 2.6 Placement Of The Ceramic Logs………………………………. 2.7 Operating Instructions ………………………………………….. 2.8 Spillage …………………………………………………………… 2.9 Customer Education ……………………………………………. 3 Servicing Instructions 3.1 Replacement Parts………………………………………………. 17 User Instructions 4 Important...

Ecoburn (S3) Gas CF Stove Installation and Servicing 1.1 - Conditions Of Installation Before installation, check that the local distribution conditions, nature of the gas and pressure, and adjustment of the appliance compatible. It is the law that only a competent person installs all gas appliances ie: a gas registered installer in accordance with the current edition of the gas safety (installation and use) regulations or the rules in force, failure to do so could lead to prosecution. The installer must be gas safe registered. The installation must also be in accordance with all relevant...

Ecoburn (S3) Gas CF Stove Installation and Servicing 1.2 - FLUE & CHIMNEY SUITABILITY MINIMUM DIMENSION OF FLUES 125 mm DIAMETER. MINIMUM EFFECTIVE HEIGHT OF ALL FLUE TYPES 3 METRES. This appliance is designed for use with conventional brick built or lined chimneys, all flues must conform to the following minimum dimensions : Before commencing installation a flue or chimney should be inspected to ensure that all of the following conditions are satisfied : 1. Check that the chimney / flue only serves one fireplace and is clear of any obstruction, any dampers or register plates must be...

Ecoburn (S3) Gas CF Stove Installation and Servicing Ecoburn (S3) Gas CF Stove Installation and Servicing WARNING This stove is fitted with a spillage monitoring system consisting of a thermal switch, which shuts the appliance off in the event of a blocked flue or inadequate flue pull occurring. The system shall not be adjusted by the installer or shall not be put out of action. When the spillage monitoring system is required to be replaced, only original manufacturers parts shall be used. If the stove switches off for no apparent reason, the appliance should not be used until expert advice...

Ecoburn (S3) Gas CF Stove Installation and Servicing 2.3 - FLUE CONNECTION The flue should be at least 3m high and at least 125mm diameter (5”) at no point should there be any negative or horizontal gradients in the flue pipe. It is recommended that a minimum height of 600mm from the stove before any significant change of direction of the flue. 2.4 - VENTILATION Ventilation should be in accordance with national regulations in the UK purpose provided ventilation is not normally required BS5871 part 1 and in IE IS813 (IE Only). 2.5 - GAS CONNECTION The gas connection can be made by removing...

Ecoburn (S3) Gas CF Stove Installation and Servicing 2.6 - PLACEMENT OF THE CERAMIC LOGS WARNING—DO NOT CHANGE THE FUEL BED LAYOUT, THE TYPE OR NUMBER OF LOGS. Contents Of Log Fuel Effect Kit -

Ecoburn (S3) Gas CF Stove Installation and Servicing Fitting Procedure For Log Set Layout - Ecoburn (S3) Gas CF Stove Installation and Servicing Scatter the bag of embers, evenly over the grate and burner, as shown above, ensuring the pilot and pilot shield are left clear from embers as indicated. Place Log 1 as shown above.

Ecoburn (S3) Gas CF Stove Installation and Servicing Position Log 2 as shown above. Note, this log rests upon the corner of log 1. STEP 4 Position Log 3 as shown above.

Ecoburn (S3) Gas CF Stove Installation and Servicing Position Log 4 as shown above, centrally at the rear of the burner. STEP 6 Position Log 5 as shown above, centrally resting upon Logs 2 & 4.