*myarchiexpo

AD-410

Product catalog summary

Specifications:
The AD-410 model has a maximum dry weight capacity of 410 lb (185.97 kg). The tumbler diameter is 68-3/4 inches (174.63 cm) and depth is 66-3/8 inches (168.61 cm), with a volume of 143 cubic feet (4049.309 L). The tumbler/drive motor is rated at 7-1/2 hp (5.59 kW), and the blower/fan motor varies between 15 hp (11.2 kW) for gas and 25 hp (18.7 kW) for steam. The door opening measures 38 inches wide by 50 inches high (96.52 cm x 127 cm), and the door sill height is 39-3/4 inches (100.97 cm).

Gas Model:
Available voltages range from 208-575v, 3-phase, 3 or 4 wire, 50/60 Hz. The approximate net weight is 6,300 lb (2,857.63 kg) and shipping weight is 6,800 lb (3,084.43 kg). Airflow is 9,200 cfm (260.52 cmm) with a heat input of 1,400,000 Btu/hr (352,794 kcal/hr). The exhaust connection diameter is 28 inches (71.12 cm).

Steam Model:
Available voltages are the same as the gas model. The net weight is 6,800 lb (3,084.43 kg) and shipping weight is 7,300 lb (3,311.22 kg). Airflow is 10,300 cfm (291.66 cmm) with steam consumption at 1,257 lb/hr (570.17 kg/hr) and a maximum operating steam pressure of 125 psi (8.62 bar).

Electrical Service Specifications:
For both gas and steam models, it is crucial to specify the correct voltage when ordering, as 208 VAC and 230/240 VAC are not the same. Circuit breakers must be thermal/magnetic motor curve type, and for 3-phase dryers, they must be 3-pole type.

Installation Notes:
Both gas and steam tilting units require clean, dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). Ductwork size and piping to the dryer vary with installation conditions, and exhaust static pressure should not exceed 0.3” water column (0.74 mb). Contact the factory for assistance with specific installation requirements.

Catalog excerpts

AD-410 NON-TILT* 1-DOOR GAS MODEL Gas, 1-Door, All-Tilt, *Rear Exhaust* - Electrical Service Specifications AD-410 NON-TILT* 1 -DOOR STEAM MODEL Steam, All-Door, All-Tilt, *Side Exhaust* - Electrical Service Specifications QY160051 1/17 88 Currant Road, Fall River, MA 02720-4781 • 508.678.9000 • www.adclaundry.com

Open the catalog to page 1

AD-41 O* 2-DOOR GAS MODEL * Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). ** Ductwork size varies with installation conditions. Exhaust static pressure should not exceed 0.3” water column (0.74 mb). *** Size of piping to dryer varies with installation conditions. Contact factory for assistance. * Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). ** Ductwork size varies with installation conditions. Exhaust static pressure should not exceed 0.3”...

Open the catalog to page 2

AD-410 TILTING* 1-DOOR/2-WAYTILTGAS MODEL * Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). ** Ductwork size varies with installation conditions. Exhaust static pressure should not exceed 0.3” water column (0.74 mb). *** Size of piping to dryer varies with installation conditions. Contact factory for assistance. AD-410 TILTING* 1-DOOR/2-WAYTILT STEAM MODEL * Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). ** Ductwork size varies with installation...

Open the catalog to page 3

* Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). ** Ductwork size varies with installation conditions. Exhaust static pressure should not exceed 0.3” water column (0.74 mb). *** Size of piping to dryer varies with installation conditions. Contact factory for assistance. LM ' au.WER , iwrl'llOllfl J9 "DIX)II �--=t----::,:'.:=:==-'--;,'---1l- �� f'FP.T. s.AP.£ W'Al'EII CCNIECmN AD-410 TILTING* 1-DOOR/FORWARD-TILT STEAM MODEL * Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ±...

Open the catalog to page 4

* Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). ** Ductwork size varies with installation conditions. Exhaust static pressure should not exceed 0.3” water column (0.74 mb). *** Size of piping to dryer varies with installation conditions. Contact factory for assistance. * Both gas and steam tilting units must be supplied with clean dry, regulated air at 80 PSI ± 10 PSI (5.52 Bars ± 0.69 Bars). ** Ductwork size varies with installation conditions. Exhaust static pressure should not exceed 0.3” water column (0.74 mb)....

Open the catalog to page 5