*myarchiexpo

AD-310 Models

Product catalog summary

Specifications:
The AD-310 models have a maximum capacity of 310 lb (140.61 kg) and a minimum load size of 205 lb (92.99 kg). The tumbler diameter is 62-1/2 inches (158.75 cm) with a depth of 60 inches (152.40 cm), resulting in a volume of 106.50 cu ft (3,015.744 L). The door opening measures 36-3/4 inches by 43 inches (93.35 cm x 109.22 cm). The cabinet width is 82-1/2 inches (209.55 cm), and the operating depth varies depending on the door configuration.

Electrical and Motor Specifications:
The models operate on voltages ranging from 208 to 575 volts, with a 3-phase, 3 or 4-wire service, and 50/60 Hz frequency. The tumbler/drive motor is rated at 5 hp (3.73 kW), while the blower/fan motor varies between 15 hp and 25 hp (11.19 kW to 18.64 kW).

Gas and Steam Models:
The gas models have a heat input of 1,125,000 Btu/hr (283,495 kcal/hr) and require a maximum gas pressure of 12 in WC (29.89 mb). The steam models consume 1,153 lb/hr (522.99 kg/hr) of steam and have a boiler horsepower of 35 Bhp.

Airflow and Exhaust:
The airflow for gas models is 6,500 cfm (184.06 cmm), while steam models have an airflow of 8,500 cfm (240.69 cmm). Both models have a maximum exhaust back pressure of 0.3 in WC (0.75 mb) and an exhaust diameter of 24 inches (60.96 cm).

Compressed Air Requirements:
Compressed air pressure is maintained at 80 psi (± 10 psi) (5.52 bar ± 0.69 bar), with a volume of 11 cfh (0.31 cmh) for both 1-way and 2-way tilt configurations.

Electrical Service Specifications:
The document provides detailed electrical service specifications for different voltage configurations, emphasizing the importance of specifying the correct voltage when ordering. Circuit breakers must be thermal/magnetic motor curve type, and specific wire sizes are recommended for each voltage.

Model Variants:
The AD-310 series includes various configurations such as tilting and non-tilting models, with options for steam or gas operation, and different door and tilt configurations.

Catalog excerpts

AD-310* NON-TILT THERMAL OIL WITH DAMPERQY160050 1/17 88 Currant Road, Fall River, MA 02720-4781 • 508.678.9000 • www.adclaundry.com

Open the catalog to page 1

BOTH GAS AND STEAM TILTING UNITS MUST BE SUPPLIED WITH CLEAN, DRY, REGULATED AIR AT 80 PSI ± 10 PSI (5.52 BAR * .69 BAR). DUCTWORK SIZE VARIES WITH INSTALLATION CONDITIONS. EXHAUST STATIC PRESSURE SHOULD NOT EXCEED 0.3' WATER COLUMN (0.74 mb). LINT DRAWER (OUT FRONT) SIZE OF PIPING TO DRYER VARIES WITH INSTALLATION CONDITIONS. CONTACT FACTORY FOR ASSISTANCE. 108 3/4 in **24' DIA EXHAUST DUCT CONNECTION 69 in 175.26 cm ■FRONT ELECTRICAL CONNECTION (BEHIND FRONT PANEL) 30 3/4 in 75 in 78.11 cm 190.5 cm ■ DOOFH 151 SILL -f--*24' DIA EXHAUST DUCT CONNECTION ' (OUT REAR) 108 3/4 in 278.66 cm 15.56...

Open the catalog to page 2

BOTH GAS AND STEAM TILTING UNITS MUST BE SUPPLIED WITH GLEAN, DRY, REGULATED AIR AT 80 PSI */- 10 PSI (552 BAR +/- 0.62 BAR) DUCTWORK SIZE VARIES WITH INSTALLATION CONDITIONS. EXHAUST STATIC PRESSURE SHOULD NOT EXCEED 0.3" WATER COLUMN (0.74 mb). 5 ZE OF P P NG TO DRYER VARES W TH NSTALLATQN C0ND T QN5. CONTACT FACTORY FOR ASS STANCE **** THE FIRE SUPPRESSION SYSTEM MUST BE SUPPLIED WITH WATER AT A PRESSURE OF 40 PSI MIN./100 PSI MAX. (2.8 BAR MIN./6.9 BAR MAX.) EXHAUST DUCT LINT DRAWER- EXHAUST DUCT CONNECTION (OUT REAR) FRONT VIEW AD-310* NON-TILT STEAM MODEL BOTH GAS AND STEAM TLTNG UN T5...

Open the catalog to page 3

BOTH GAS AND STEAM TILTING UNITS MUST BE SUPPLIED WITH CLEAN. DRY. REGULATED AIR AT DUCTWORK SIZE VARIES WITH INSTALLATION CONDITIONS. EXHAUST STATIC PRESSURE SHOULD NOT EXCEED 0.3' WATER COLUMN (0.74 mb). *** SIZE OF PIPING TO DRYER VARIES WITH INSTALLATION CONDITIONS. CONTACT FACTORY FOR ASSISTANCE EXHAUST DUCT. FRONT VIEW EXHAUST DUCT INLET CONNECTION DOOR SILL LOAD POSITION \ FRONT ^ELECTRICAL CONNECTION -3/4' FJiP.T. WATER CONNECTION

Open the catalog to page 4

BOTH GAS AND STEAM TILTING UNITS MUST BE SUPPLIED WITH CLEAN, DRY, REGULATED AIR AT 80 PSI ± 10 PSI (5.52 BAR ± .69 BAR). DUCTWORK SIZE VARIES WITH INSTALLATION CONDITIONS. EXHAUST STATIC PRESSURE SHOULD NOT EXCEED 0.3’ WATER COLUMN (0.74 mb). SIZE OF PIPING TO DRYER VARIES WITH INSTALLATION CONDITIONS. CONTACT FACTORY FOR ASSISTANCE. -FRONT ELECTRICAL CONNECTION **24" DIA EXHAUST DUCT CONNECTION 138.11 *«24* DIA EXHAUST DUCT CONNECTION (OUT REAR) 3/4' FJiP.T. WATER CONNECTION- **24’ DIA EXHAUST DUCT CONNECTION UNLOAD POSITION LINT DRAWER ELECTRICAL CONNECTION ** 1 1/2'DIA GAS INLET CONNECTION...

Open the catalog to page 5