USER’S MANUAL

Reproduction, even partial, of this document without written permission by the manufacturer is strictly forbidden. The manufacturer assumes a policy of continual improvement and reserves the right to modify this document without prior notice on condition that the changes do not constitute health and safety risks. © 2008 - Text, illustrations and page layout by Tipolito La Zecca. The text may be reproduced, in whole or in part, on condition that the author is mentioned.

GENERAL INFORMATION This manual forms an integral part of the appliance and was produced by the Manufacturer to provide the necessary information to people authorised to interact with it during its working life. Operators of the appliance must adopt correct working practices and must carefully read and follow all the instructions contained in this manual. This manual is written by the Manufacturer in the original language of Italian and may be translated into other languages to meet legal and/or commercial requirements. Carefully read the instructions contained in this manual to avoid any unnecessary...

IDENTIFICATION OF MANUFACTURER AND EQUIPMENT The nameplate shown here is applied directly onto the appliance. It contains references and all the information essential for safely operating the device. For any technical requirements, please contact the Manufacturer’s Technical Service Centre or an authorised dealer. For technical assistance, please indicate the data reported on the identification plate, the approximate hours of use and the type of fault detected. DATA PLATE Manufactured by Xxxxxxxxxxxxxxxxxx, Xxxxxxxxxxxxxxxxx XXXXX Xxxxxxxxxxxxxxxxxxxxxxxx (XX) - XXXX B. CE conformity label. C....

• Never allow people to sit on the robot. Never lift the robot to inspect the blade or to carry it while it is running. Do not place hands and feet under the robot when it is in operation. EN • Do not use the robot when a sprinkler system is running. In this case, program the robot and the sprinkler system so that they do not operate at the same time. Do not wash the robot with high-pressure water jets and do not immerse it in water, partially or completely, as it is not watertight. • Disconnect the power supply and activate the safety device before performing any adjustment or maintenance that...

A Read user instructions carefully - to understand meanings before j—t—u using the machine. Keep an adequate safe distance from the machine while it is running. Do not touch the rotary blade and do not place your hands or feet underneath the machine when it is running. Wait until the blade and rotating parts come to a complete stop before accessing. While the robot is working, make sure there are no people in the working area (especially children, elderly or disabled people) and pets. Keep children, pets and other people at a safe distance when the machine is functioning. To prevent...

(*) Depends on the condition of the grass, lawn and the complexity of the mowing area. User's manual

(*) Depends on the condition of the grass, lawn and the complexity of the mowing area. GENERAL DESCRIPTION OF THE APPLIANCE The appliance is a robot designed and built to automatically cut RANDOM OPERETION grass in gardens and lawns at any time of the day. It is small, compact, silent and easy to handle depending on the type of lawn that is being mowed. During operation, the robot mows the area delimited by paving and/or barriers (fences, walls, etc.). When the robot detects that there is no grass or encounters an obstacle, it changes route in a random manner and starts mowing again in a new...

User's manual

INSTALLATION PACKING AND UNPACKING The equipment is delivered suitably packaged. When unpacking, carefully remove and check the integrity of the parts. Warning – Caution Keep plastic wrapping and plastic containers away from infants and children: risk of suffocation! Important Keep the packaging materials for future use. PLANNING OF SYSTEM INSTALLATION The robot is not difficult to install, but requires some preliminary planning in order to define the best area for installing the power supply unit. Position the power supply unit in an easy to access zone. The power supply unit must be in a well-ventilated...

PREPARATION AND MARKING THE BOUNDARIES OF THE WORK AREAS preparation of the lawn to be mowed EN 1. Make sure that the lawn to mow is even and does not contain holes, stones or other obstacles. Otherwise, prepare the lawn by filling in any holes and removing any obstacles. If some obstacles cannot be removed, it is necessary to properly define and protect the interested areas. 2. Check that all the areas of the lawn do not exceed the allowable slopes (see “Technical Specifications”). The sensors, which recognise the presence of the grassy surface, allow the robot to move freely inside the lawn....

The work area can also be effectively delimited by hedges. The work area cannot be delimited by ditches or holes which must not be present inside the grassy area to mow. Before starting the robot, check that there are no objects on the lawn such as toys, small stones, branches or sprinklers protruding from the ground which could impede correct functioning or cause damage to the blade. The illustrations show an example of the internal and peripheral elements of the correct work area. If elements such as tree roots or exposed wires are present, it is necessary to delimit the perimeter of these...

Do not, under any circumstance, leave areas which have not been delimited by barriers inside the work area, as these will prevent the robot from functioning properly (roots, external pipes, work tools, etc.). Fine gravel Danger - Attention If fine gravel, leaves or small stones are used to border the lawn, they are not detected correctly by the robot. Protect the lawn with other borders. Sharp corners Danger - Attention In areas of the lawn that end in narrow spaces as shown in the figure, the robot cannot move easily, therefore this part of the lawn must be excluded because the robot would exit...