ALPOLIC® /fr Composite Fire-Rated Panels
3Pages

ή Mitsubishi Plastics Composites America, Inc. framing members to anchors, anchor deflec - tion in any direction should not exceed 1/16" (1.6 mm). Allow for free horizontal and vertical thermal movement, due to expansion and contraction of components over a tempera - ture range. Fabrication, assembly and erec - tion procedures should take into account the 1. Product Name ambient temperature range at the time of ALPOLIC/fr Composite Fire-Rated Metal Panels the respective operation. Wall design should feature provisions to drain to the exterior face 2. Manufacturer of the wall any leakage of water at joints and Mitsubishi Plastics Composites America, Inc. any condensation that can occur within the 401 Volvo Parkway construction. Chesapeake, VA 23320 (800) 422-7270 4. Technical Data Fax: (757) 436-1896 E-mail: info@alpolic.com APPLICABLE STANDARDS www.alpolic-northamerica.com ASTM International ʕ 3. Product Description Strength on Flat Sandwich Constructions in BASIC USE Flatwise Plane Sound Insulation Օ ALPOLIC/fr Composite Metal Panels are used Performance of Building Assemblies by American Architectural Manufacturers Associ- for cladding of non-residential and residential Means of a Calibrated Hot Box (Withdrawn ation (AAMA) - AAMA 2605 Voluntary structures. They are manufactured, fabricated 2002) Specification, Performance Requirements and and installed to withstand stress from ʕ Test Procedures for Superior Performing Organic deflection and thermal movement and to main - Coefficient of Linear Thermal Expansion of Coatings on Aluminum Extrusions and Panels tain performance criteria stated by the Plastics Between -30C and 30аC With a Underwriters Laboratories of Canada, Ltd. manufacturer. Vitreous Silica Dilatometer (ULC) - CAN/ULC S134M COMPOSITION & MATERIALS ҕ APPROVALS ALPOLIC/fr Composite Fire-Rated Metal Panels Climbing Drum Peel for Adhesives International Building Code (IBC) Research are composed of 3 or 4 mm thick, mineral filled Report Number NER 672 fire resistive thermoplastic core material that Determining Ignition Temperature of Plastics meets performance characteristics specified Օ National Building Code (Canada) when fabricated into composite assembly. Face Testing of Metallic Materials City of New York MEA 142-99-E sheets are aluminum 3105-H14 alloy, or equiva - City of Los Angeles RR 25362 lent, 0.020" (0.51 mm) thick. Sheets are thermally Conducting Strength Tests of Panels for bonded in continuous process to core material. Building Construction Miami Dade NOA 06-0531.12/.13 FINISHES Օ PHYSICAL/CHEMICAL PROPERTIES Burning Characteristics of Building Materials ALPOLIC/fr panels are available with fluorocar - Tested for resistance to delamination as fol - bon and polyester coatings. The fluorocarbon for Fire Tests of Roof Coverings lows: finish is a Lumiflonժ based resin. Lumiflon-based Օ fluoropolymer resin coatings meet or exceed Tests of Building Construction and Materials minimum values expressed in AAMA 2605 where relevant Օ to coil coatings. Stainless steel and titanium Determining the Rate of Air Leakage Through (100 N-m/m) minimum finishes are available. Exterior Windows, Curtain Walls, and Doors 8 hours of submersion in boiling water and COLORS Under Specified Pressure Differences Across after 21 days of immersion in water at A pallet of bright, vibrant and vivid colors in a the Specimen 70 degrees F (21 degrees C) wide gloss range is available. A Class 1 anodized Օ finish is available, as well as a stone series finish. Structural Performance of Exterior Windows, -6 Curtain Walls, and Doors by Uniform Static Air 13 ՗ 10 in/in/F LIMITATIONS Pressure Difference Е Deflection of perimeter framing member (44 MPa) should not exceed L/175 normal to plane of Penetration of Exterior Windows, Curtain Օ the wall; deflection of individual panels should Walls and Doors by Uniform Static Air Pressure (49 MPa) not exceed L/60. At connection points of Difference > SPEC-DATA ժ and MANU-SPEC are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style of The Construction Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ʩ2009 Reed Construction Data. All Rights Reserved. TM size="-2">

ή Mitsubishi Plastics Composites America, Inc. avoid construction delays. Submit shop draw - ings showing layout, profiles and product components, including anchorage, accesso - ries, finish colors and textures. Include details showing thickness and dimensions of various system parts, fastening and anchoring meth - ods, locations of joints and gaskets, and loca - tion and configuration of joints necessary to accommodate thermal movement. Submit selection and verification samples for finishes, colors and textures. Delivery & Storage Deliver materials in manufacturers original, unopened,...

ή Mitsubishi Plastics Composites America, Inc. 7. Warranty Contact manufacturer for information on warranty conditions, exclusions, duration and remedies. 8. Maintenance These panels, when properly installed, require no specific maintenance. An occasional pres - sure washing can be required depending on local environmental conditions. Periodic inspection for sealant integrity is advised to ensure long-term system performance. 9. Technical Services A staff of trained personnel offers design assis - tance and technical support. For technical assistance, contact ALPOLIC, Mitsubishi Plastics...