ή Mitsubishi Plastics Composites America, Inc. FINISHES ALPOLIC ALPOLIC Օ 1. Product Name Օ ShAPES Material Panels (TCM) ALPOLIC Օ and formed using coated carbide cutting Composite Material Panels (SCM) tools. Angle bends are formed by routing the back of the panel prior to shaping. The com - 2. Manufacturer mon pan shape is formed by routing the back Mitsubishi Plastics Composites America, Inc. edges, trimming the corners and bending and 401 Volvo Parkway reinforcing Chesapeake, VA 23320 fabrication recommendations. (800) 422-7270 ALPOLIC Fax: 4-stand roll bender to a curved shape for E-mail: curved corners or column covers. Bumping on www.alpolic-northamerica.com a press brake also can be used to produce a curved 3. Product Description APPLICATIOn 4 mm panels is as small as 4" (102 mm). ALPOLIC BASIC USE another or to other materials by conventional ALPOLIC 4. Technical Data methods of attachment - rivets, bolts or Material (TCM) and Stainless Steel Composite APPLICAbLE screws. For interior installation, flat surfaces of Material (SCM) panels are widely used as ASTM International ALPOLIC interior - ʕ as gypsum board using double-faced tape or cial and institutional applications. These pan - Properties of Sandwich Constructions nonhardening adhesive. els variety of fabrication techniques. PrECAuTIOnS Strength of Plastics by Punch Tool ALPOLIC COmPOSITIOn Օ products requiring care in handling to avoid TCM and SCM are composite materials newly Testing of Metallic Materials damage to the finish. Handle, store, install and developed by Mitsubishi Plastics Composites clean panels following the manufacturerՒs America, Inc. TCM is 4 mm thick and is com - Burning Characteristics of Building Materials instructions. Comply with manufacturers recom - posed of polyethylene with a 3.4 mm thick ҕ mendations - noncombustible mineral filled core sand - for Fire Tests of Roof Coverings tion wiched between a surface skin of titanium 0.3 mm thick and backside skin of stainless steel Insulation 6. Availability & Cost 0.3 mm thick. SCM is also 4 mm thick and is PhySICAL/ChEmICAL composed of polyethylene with a 3.4 mm AvAILAbILITy See Table 1. thick noncombustible mineral filled core sand - ALPOLIC wiched between two 0.3 mm thick stainless FIrE through the regional offices of Mitsubishi Plastics steel sheets. Surface burning characteristics Composites America, Inc., Com posite Materials Օ Division. Contact Mitsubishi for the location of SIZES an ALPOLIC Օ COST - Pass Օ Contact the area representative or the MPCA 5. Installation home to project size, finish selection and panel sizes. ALPOLIC PrEPArATOry Օ The manufacturer recommends field measure - 7. Warranty ment prior to fabrication. Verify alignment of Contact the manufacturer for information on Օ surfaces to receive panels. panel and finish warranties. > SPEC-DATA and MANU-SPEC ʪ are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style of The Construction Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. 2009 Reed Construction Data. All Rights Reserved. TM size="-2">

ALPOLIC TCM ALPOLIC SCM metal > 2 0.4 mm thick panel 9.3 10.2 Thermal 0.52 0.52 Tensile > 2 7.0 8.6 yield > 2 6.1 7.0 Elongation (ASTM E8), % 11.1 12.6 deflection 112 117 Sound transmission loss (ASTM E413), STC 25 30 Flexural > 2 5000 7200 Flexural > 2 /mm 27 > 3 38 > 3 Punching shear resistance > 1 (ASTM D732), kg 3080 3517 Punching > 2 4.9 5.6 Product Tolerance Width, 2.0 ѱ 2.0 Length, 4.0 ѱ 4.0 > SPEC-DATA ժ and MANU-SPEC are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style of The Construction Specifications Institute and is used with...