THE EXTRA-LARGE FORMWORK PANEL
32Pages

THE EXTRA-LARGE FORMWORK PANEL

MaxiDalle | The extra-large formwork panel

The MaxiDalle range is a panel-type formwork system for large cells. The high-performance system is capable of supporting a concrete slab of up to 50 cm in thickness. Simple: MaxiDalle comprises a single prop head for all assembly configurations and a formwork panel that comes in four sizes. A snap-on joint provides complete sealing of the formwork. Fall from height NF E 85-014 Fall on ground level NF E 85-014 Strenuous Postures positions Manual load handling NF X 35-109 Manutention manuelle SAFETY AND ARDUOUSNESS PERFORMANCE CHARACTERISTICS MaxiDalle is the best-performing panel formwork...

MaxiDalle | The extra-large formwork panel PRODUCTIVITY High installation work rate. Flexible use thanks to the various solutions for handling compensations (sheet, batten, H20 beam support). A single head for all configurations. Joint can be reused up to 5 times. Ergonomic panel handling tool: MaxUpDown. QUALITY The insertion of the formwork pa nels combined with the snap-on joint creates a quality facing. The flashing left by the joint is admired for its clean and neat appearance. The joint seals the panel and enables the use of self-levelling concrete. SAFETY Ground-based fitting and...

WITHOUT MAXUPDOWN MAXUPDOWN HELPS INCREASE THE WORK RATE TO 40 M² /PERSON/DAY ERGONOMICS Lightweight panels: 28 kg for the 120 x 150 cm panel. 2 workers are sufficient for handling, in compliance with labour regulations. At extra-high heights, the MaxUpDown tool enables easier panel handling and helps reduce repetitive strain injuries. WITH MAXUPDOWN

MaxiDalle 3 SIMPLE COMPONENTS 1 Head (prop + plate) rop with 120 x 120 mm plate, bore holes spaced P at 80 mm axiDalle plate: a single model for all assembly M configurations 4 panel sizes ossible compensation system P Formwork panels Formwork panel Snap-on for quick assembly Reliable hold during all phases of formwork and casting Reusable (number o

MAXIDALLE ACCESSORIES Mesh* MaxiDalle adapter The wire mesh is galvanized, with polyester powder coating Galvanized post* Alphi formwork adapter* * ompliant with EN 13374 C standard Leborgne tools Nanovib® range Tools suitable for fitting and removing Alphi formwork: hammers, hammer holder, prop key Vibration and noise reduction distributes Click here to view details of Leborgne Too

MaxiDalle MAXIDALLE ACCESSORIES Compensation support Formwork removal pole Gauge stick Compensation plate Support for H20 beam and 18 mm plywood Compensation batten (to receive 15 mm plywood)

Maximum working height (m) Unit weight including cylinder (kg) Maximum working height (m) Unit weight including cylinder (kg)

MaxiDalle MAXIDALLE ACCESSORIES Bracket Boundary barrier Assembled unit Barrier + ballast + tube

Skin clamp Girder clamp Prop clamp Stabilising clamp for use with 48 mm tube and collars The tube is inserted into the prop used for cladding The 45°-oriented rear plate allows retrospective fastening with the prop

▼ The mesh is locked at the top by the anti-lifting pin and locked in rotation at the base. Installation of AlphiSafe safety system in cantilever configuration from bottom AlphiSafe is a collective protection system for formwork and slab edges. The technical innovations in the system allow safe installation and automatic locking. Robust AlphiSafe is certified by Ginger CEBTP, as per the EN 13374 standard of July 2013, as class A and B for some components. AlphiSafe is distinguished by its height of 1.30 m, which is above the minimum height of 1.00 m set by the standard, and protects...

USER GUIDE STABILISATION Cross-member frame - axiDalle must be stabilised at cell M commencement and during cell installation. - or cells greater than 100 m 2 F in size or on commencing, intermediate stabilisations should be added, every 100 m2, using cross-member frames or clamps. - stabilisation solutions can be 3 used at commencement. - Cross-member frame system. - cross-member frame is fitted provisionally A on the first 4 props. Skin clamp Skin clamp - Skin clamp + tube system. - et up the stabilisation of the first components. S - nce in place, the tripods can be removed. O Girder...

MaxiDalle MAXIDALLE INSTALLATION WITH TRIPODS1 Panel installation should start on the side of the arrow indicated in the installation drawing. - nstall 4 props equipped with MaxiDalle tie plates, using tripods. I - it the first panel flat using a rolling safety ladder. F - sing the gauge stick, the form fitter raises the panel safely, until it is U in the horizontal position. - ttach the second panel vertically to the props. A - hilst keeping the panel resting on the gauge stick, the form fitter W installs the props.

CONTINUED INSTALLATION WITH SKIN CLAMPS 5 S tabilisation can be performed using skin clamps, prop clamps or cross-member frames. - itting of skin clamps suitable for use for formwork stabilisation. F - aise the first panel using the gauge stick, and hold it in the horizontal R position. - osition the first prop of the second frame against the wall and complete P the stabilisation with skin clamps. - tart the second frame by hanging the first panel. S - aise the second panel using a second gauge stick and position the R next prop - Continue from one to the next.

MaxiDalle MAXIDALLE INSTALLATION WITH TRIPODS9 - he cell is formed and the slab is cast. T

MAXIDALLE FORMWORK REMOVAL WITH ROLLING SAFETY LADDERS 1 If applicable, start formwork removal with a panel close to a compensation zone. - The panel to be removed is held by 4 props - emove the props on the side of the free edge of the panel. The panel R cannot fall as it is fixed onto the rear props. - Remove the rear props. - Lower the panel to be removed. - Continue from one to the next. - osition the rolling safety ladders on either side of the panel to be removed. P - Remove the final holding prop. - f required, the slab may be shored underneath by drying props. I

MaxiDalle MAXUPDOWN FOR MAXIDALLE MaxUp is a tool enabling MaxiDalle formwork panels to be fitted effortlessly onto prop heads. MaxDown is a tool enabling easier MaxiDalle formwork panel removal at extra-high heights. Protective netting receives and secures the panel as it is lowered. Fall from height NF E 85-014 Fall on ground level NF E 85-014 Strenuous Postures positions Manual load handling NF X 35-109 Manutention manuelle Excellent SAFETY AND ARDUOUSNESS PERFORMANCE Médiocre CHARACTERISTICS Fitters work at ground level (no need for rolling safety ladder). They no longer need to handle...