PLAFONE
4Pages

Smoke exhaust dampers and air inlets} Fire protection PLAFONE Smoke exhaust damper Presentation of the new PLAFONE tunnel damper range Compliance ' Compliant with CE marking as per EN 12101-8: 1812 - CPD -1054. ' EI 120 (ved-ho-i ** o) S -1500 Pa - AA multi. ' Certified & " and compliant with NF-S-61937-10. Advantages • Minimal leakage rate. • Validate for remote and horizontal installations. • Upgradable ISONE mechanism. PLAFONE closed in stand-by position INTRODUCTION Like gate type dampers, CE marking for tunnel dampers has been obligatory since February 2013. The new PLAFONE tunnel damper has been developed in accordance with all European and French requirements. QUALIFICATION • Compliant with CE marking as per EN 12101-8: 1812 - CPD -1054 • Fire resistance classification according to EN 136610 test: EI 120 (ved-ho-i o) S -1500 Pa - AA multi, compliant with § 7.2.4 of EN13501-4, Qualified on a Promatect L500 or EXTHAMAT smoke exhaust duct and on ducts compliant with EN 1366-9, of the same material and same density. • Compliant with NF S 61937-10. • Leakage rate: the PLAFONE damper presents an extremely low leakage rate: under 150 Pa, the leak is < 200 m3/h per m2 of vane. FIELD OF APPLICATION Tunnel smoke exhaust damper intended for public buildings, high-rise buildings, or cat. 3 and 4 residential buildings. Suitable for installation in technical ceilings. Smoke exhaust dampers are normally closed and only open in the event of a fire, on electrical command from the Fire safety control system. DESCRIPTION • The PLAFONE smoke exhaust damper is inspired by the ISONE/Ap wall-mounted damper, it features: - Two metal sleeves on either side of a refractory material structure that acts as a vane and fixing frame, - An intumescent seal and cold gasket placed between the vane and the refractory frame, to achieve the required leakage rate, - The refractory complex is drilled with holes to enable attachment to the smoke exhaust duct certified EN 1366-8 or -9, - An ISONE-type electric control mechanism is used to house an electromagnetic trip device, up to 4 signalling contacts and an EHOP reset motor. • Smoke exhaust dampers are never fitted with fuses. • The nominal X and Y dimensions of the damper correspond to the embedding dimensions in the duct (or duct air stream). Further information concerning ISONE mechanisms is available in the fire damper section. 112 Fire Protection Catalogue Edition no. 8

Presentation of the new PLAFONE tunnel damper range (■■**> PLAFONE closed in stand-by position PLAFONE open in safety position Compliance SIZE RANGES AND FREE AIR PASSAGES (dm2) PLAFONE 11041111 Smoke exhaust dampers and air inlets^ Fire protection Possibility of circular connections, diameters from 100 mm to 900 mm, using specific accessories. Free surface (in dm2) = (X-70) x (Y-120) / 1000 (X & Y in mm) for y > 400 Free surface (in dm2) = (X-52) x (Y-102) / 1000 (X & Y in mm) for y < 400 Fire Protection Catalogue Edition no. 8 113

Smoke exhaust dampers and air inlets} Fire protection PLAFONE Smoke exhaust damper New PLAFONE tunnel damper PLAFONE closed in stand-by position PLAFONE open in safety position INSTALLATION For which installation? Qualified on a Promatect L500 or EXTHAMAT smoke exhaust duct and on ducts compliant with EN 1366-8 and -9 of the same material and same density. Multi-compartment smoke exhaust dampers can be used for single-compartment installations. The fire classification stipulates the service pressure: the damper must not be subjected to pressure drops > -1500 Pa. Fire direction: like all...

• Suitable for standard suspended-ceiling tiles. • AU 123 & AU 124 series, with thin frame, for greater rigidity. FIELD OF APPLICATION • Air recovery for all ventilation & air conditioning applications. • Ceiling installation - replacing a suspended ceiling tile. DESCRIPTION AO 123 Z • Square, straight mesh - 15 x 15 mm without frame. • White epoxy painted aluminium finish, RAL 9010. AU 123 Z • Square, straight mesh - 15 x 15 mm with thin 5 mm frame. • White epoxy painted aluminium finish, RAL 9010. AU 124 Z • Square, angled mesh - 45° - 15 x 15 mm with thin 5 mm frame. • White epoxy...