カタログ >
VOLTECO >
BI MORTAR CONCRETE SEAL

BI MORTAR CONCRETE SEAL
1 / 4ページ

カタログの抜粋

WATERPROOF MORTARS/RAPID-SETTING MORTARS PRODUCT DESCRIPTION Brush-applicable cement-based waterproofing product suitable for both negative and positive hydrostatic pressure. This creates a continuous coating that is particularly resistant to impact and abrasion. PRODUCT APPLICATION • Rigid waterproofing of concrete or masonry surfaces, under or above ground, such as basins, pools, channels, foundation walls, cellars and elevator pits ADVANTAGES • Usable with negative and positive hydrostatic pressure • Suitable for both indoor and outdoor application • Excellent impermeability performance • Particularly resistant to abrasion and impact • Simple and quick brush application, excellent workability • Suitable for continuous contact with water • Easy maintenance, also in conditions of high humidity and closed environments PREPARATION AND APPLICATION Preparing the surfaces Verify the structure suitability for the hydrostatic loads; if intended to contain water, perform a preload test. Clean all traces of form oil or grease and remove any loose parts (fouling). High-pressure clean the surface until it is soaked and remove excess water before applying the product. Repair the surface with suitable Volteco mortar if the surfaces are very uneven or in the case of mixed masonry. Seal any localised water flows with TAP 3/I-PLUG rapid-setting hydraulic mortar. Preparation of elements of discontinuity on the surfaces (positive hydrostatic pressure) • CONSTRUCTION JOINTS Connect the construction joints between the bed and the vertical wall by forming a 3x3 cm fillet with SPIDY 15 rapid-setting mortar • SPACERS Remove the spacers on both sides of the wall and plaster with SPIDY 15 rapid-setting mortar • PASSING BODIES Seal all the passing bodies, including spacers and pipes, with AKTI-VO 201 mastic (see related technical data sheet) • JOINTS, CRACKS AND EDGES Connect all joints, significant cracks with GARVO or BI FLEX joint cover strip, as well as the horizontal and vertical edges (including where the fillet is) if WT 102 bentonite waterstop has not been used Contact the Volteco Technical Service before intervening on the expansion joints.

カタログの1ページ目を開く

WATERPROOF MORTARS/RAPID-SETTING MORTARS BI MORTAR CONCRETE SEAL Preparation of elements of discontinuity on the surfaces (negative hydrostatic pressure) WATER FLOWS Seal any water inflow with TAP 3/I-PLUG quick-setting mortar (see the related technical data sheet) CONSTRUCTION JOINTS AND CRACKS Seal the construction joints and cracks with AKTI-VO 201 mastic and/or BI FLEX system (see the relative technical data sheets) PASSING BODIES Seal all the passing bodies, including spacers and pipes, with AKTI-VO 201 mastic (see related technical data sheet) JOINTS Contact the Volteco Technical...

カタログの2ページ目を開く

WATERPROOF MORTARS/RAPID-SETTING MORTARS Specific weight > 1.85 kg/l SAFETY This is a non-toxic alkaline product. It is recommended to use a mask and gloves while working. In case of accidental contact with skin or eyes, wash thoroughly with water and consult a doctor. V0LTEC0 S.p.a Via delle Industrie, 47 - 3105Q Ponzano Veneto (I) 17 0028-CPR-2017/02/15 1370-CPR-1299 EN 1504-2:2005 BI MORTAR CONCRETE SEAL Protection systems of the concrete surface: Moisture content control (MC) and increased resistivity (IR) coating Reaction to fire: Class A1 Water vapour permeability: Class...

カタログの3ページ目を開く

WATERPROOF MORTARS/RAPID-SETTING MORTARS BI MORTAR CONCRETE SEAL The before-after sales technical/trade information of the sales network have the same validity as this document. Powered by TCPDF (www.tcpdf.org)

カタログの4ページ目を開く