カタログ >
MAPEI >
ULTRABOND P980 1K

ULTRABOND P980 1K
1 / 4ページ

カタログの抜粋

One-component, solvent-free polyurethane adhesive with a very low emission level of volatile organic compounds for pre-finished, multi-layered parquet WHERE TO USE Bonding pre-finished, multi-layered parquet, preassembled work-tops and all shapes and types of multi-layered elements on any kind of substrate. Particularly suitable for heated substrates. Odourless and completely free of solvents and free amines, may be used by installers allergic to epoxy-polyurethane products. Some application examples Ultrabond P980 1K is used for bonding pre-finished, multi-layered parquet elements on cementitious screeds, screeds made using Mapecem, Mapecem Pronto, Topcem, Topcem Pronto and similar products, old wooden floors, ceramic, marble, terrazzo, etc., and anhydrite screeds. Also suitable for heating substrates. TECHNICAL CHARACTERISTICS Ultrabond P980 1K is a one-component, solventfree polyurethane adhesive with no amines or epoxy resin, with a very low emission level of volatile organic compounds (EMICODE EC1 R). The product has been developed in MAPEI’s own research laboratories and has the following characteristics: • completely free of solvents and amines; • GEV certified as a product with a very low emission level of volatile organic compounds (EMICODE EC1 R); • one-component, supplied ready to use. If stored correctly, leftover quantities of the product may be used at a later date; • may also be used by floor-layers allergic to epoxy and epoxy-polyurethane products; • 20-30% higher yield compared with conventional two-component products; • low viscosity; • excellent straight-line hold; • excellent workability. RECOMMENDATIONS • Before laying, make sure all rooms have windows or other suitable sealing systems. • The level of humidity in the screed must be according to current norms and regulations for laying wood, indicated in the Technical Data Sheet of the parquet. • If the substrate is not completely dry, or if the humidity is higher than the required level, we recommend applying a coat of suitable waterproofing primer, such as Eco Prim PU 1K, Primer MF, etc.

カタログの1ページ目を開く

• If there is a risk of rising damp, a vapour barrier must be laid before installing the screed. sandpaper down to bare wood and remove all dust with a vacuum cleaner. Then lay and bond the new floor dressing. • Do not use Ultrabond P980 1K at temperatures lower than +10°C or higher than +25°C. Anhydrite substrates: after sanding the substrate, remove all dust with a vacuum cleaner, apply a coat of Eco Prim PU 1K, Eco Prim PU 1K Turbo or Triblock P and then start laying and bonding the new dressing. • Only lay floors if the walls and floors in the room are completely dry. APPLICATION...

カタログの2ページ目を開く

TECHNICAL DATA (typical values) PRODUCT IDENTITY creamy paste Density (g/cm³): Brookfield Viscosity (mPa·s): Hazard classification according to EC 1999/45: harmful. Before using refer to the “Safety instructions for preparation and application” paragraph and the information on the packaging and Safety Data Sheet EC1 R - very low emission level Customs class: Application temperature range: Open time (formation of skin): Adjustment time: Set to light foot traffic: Sanding of pre-assembled elements: FINAL PERFORMANCE Shore A hardness (7 days at +23°C): Wood-concrete bond strength (N/mm²):...

カタログの3ページ目を開く

PACKAGING 15 kg aluminium bags contained in plastic drums. STORAGE 12 months in its original, well-sealed packaging stored under normal conditions. When transported over long distances, an insulated container may be needed. SAFETY INSTRUCTIONS FOR PREPARATION AND APPLICATION Ultrabond P980 1K may cause serious damage if it comes into contact with the eyes. The product does not give off harmful fumes at room temperature and under normal application conditions. At high temperatures (> +60°C) small quantities of isocyanates may form, which could cause rashes in those subjects allergic to such...

カタログの4ページ目を開く