カタログ >
MAPEI >
MAPEFLEX PU30

MAPEFLEX PU30
1 / 4ページ

カタログの抜粋

Two-component, epoxy-polyurethane sealant with high chemical and mechanical strength WHERE TO USE • ealing joints in vertical concrete structures, both S interior and exterior. • brasion resistant sealing of joints in industrial floors A subject to heavy traffic, both interior and exterior. • ealing joints in rubber and PVC floors. S Some application examples • ealing flexible joints in concrete walls. More in S general, for all vertical structures, both interior and exterior, where a thixotropic product with high resistance to chemical agents, waterproof and vapour permeability is required. • ealing joints in ceramic tile floors in areas subject S to heavy traffic such as supermarkets, industrial buildings with fork lift truck traffic, sidewalks, pedestrian crossings, arcades, squares, etc. • ealing movement joints in concrete floors in car S parks and industrial buildings subject to vehicle traffic or where a high resistance to chemicals is required. • ealing rubber and PVC flooring by filling the joints S between each single tile or the sheets. • lastic fillet seals for machine beds. E • lastic fillet seals for pipe-work, drains, man-hole E covers, etc. TECHNICAL CHARACTERISTICS Mapeflex PU30 is a two-component thixotropic sealant consisting of devoid isocyanate free polyurethane polymer (component A) and a special hardener (component B). Mixing the two components produces a uniformly coloured thixotropic paste, easily workable with a flat trowel. Mapeflex PU30 can be used on both vertical and horizontal surfaces. After hardening by chemical reaction alone, which takes place in approximately 24 hours without shrinkage, Mapeflex PU30 becomes elastic, resistant to water and heat, with high mechanical strength and abrasion-resistant properties, and a good adhesion to almost all materials that are commonly used in building. Mapeflex PU30 cannot undergo work elongation above 10%. It is therefore necessary that the concrete has completed the shrinkage phase before sealing the joints (whether the joints are expansion or distribution joints). The resistance of Mapeflex PU30 to chemicals is good; however, due to the variety of products and working conditions under which it can be used, it is advisable to carry out preliminary tests in cases of doubt. The temperature resistance of Mapeflex PU30 is between -30°C and +80°C. Mapeflex PU30 complies with Euronorm EN 15651-1 (“Sealants for external and internal façades”) with performance rating F-EXT-INT. RECOMMENDATIONS • Do not use on substrates that are subject to rising

カタログの1ページ目を開く

completely and has not completed the shrinkage phase. It is not advisable to seal during the summer season; joints are at their maximum expansion. It is preferable to seal during the autumn. • Before sealing make sure the expansion of the joints do not exceed 10% of the initial width. If otherwise, prefer sealants that have higher elongation properties or increase the width of the joint (refer to our Technical Services Department). • Do not use on bituminous surfaces where the bleeding of oils may take place. • The product may change colour if exposed to UV rays without losing any of its...

カタログの2ページ目を開く

TECHNICAL DATA (typical values) In compliance with: PRODUCT IDENTITY Classification according to EN 15651-1: thick paste fluid liquid straw-coloured transparent Density (g/cm³): Brookfield viscosity (mPa·s): 1,250,000 250 (rotor F - 5 revs) (rotor F - 5 revs) APPLICATION DATA (at +23°C - 50% U.R.) Mix ratio: Application temperature range: Initial setting time: Final setting time: Set to light foot traffic: Final cure time: FINAL PERFORMANCE Shore-A-hardness: Resistance to solvents and oils: Resistance to acids and alkalis: Maximum elongation in operation:

カタログの3ページ目を開く

PRODUCT ONLY FOR PROFESSIONAL USE. Please refer to the current version of the Technical Data Sheet, available from our website www.mapei.com All relevant references for the product are available upon request and from www.mapei.com Any reproduction of texts, photos and illustrations published here is prohibited and subject to prosecution WARNING Although the technical details and recommendations contained in this product data sheet correspond to the best of our knowledge and experience, all the above information must, in every case, be taken as merely indicative and subject to confirmation...

カタログの4ページ目を開く