ENA 8
1 / 31ページ

Your ENA 8 Control elements

8 Transport and environmentally friendly disposal 59 11 JURA contact details / Legal information 62 Symbol description Warnings J WARNING Always take note of any information marked with the words CAUTION or J CAUTION WARNING and a warning sign. The signal word WARNING draws your attention to potential serious injury, and the signal word CAUTION to potential minor injury. CAUTION CAUTION draws your attention to potential damage to the machine. Symbols used ► Prompt to take action. This symbol means that you are being prompted to perform some action. E Information and tips to make...

Control elements 1 Display 2 Mains cable (back of the machine) 3 Height-adjustable dual spout 4 Coffee grounds container 5 Drip tray 7 Water tank (with cover) 8 Multi-function buttons (button function depends on what is shown in the display) 9 Hot-water spout 10 Insert for drip tray

Bean container with aroma preservation cover Powder chute for ground coffee On/Off button Q Grinding wheel es Back of the machine: Service socket for JURA Smart Connect (behind cover). Smart Connect is not included with all models. Filler funnel for ground coffee Measuring spoon for ground coffee Container for milk system cleaning

Important information Important information Proper use The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain. A warranty service is not applicable for damage or defects caused by non-compliance with the instructions for use. Keep these...

Important information There is a risk of scalds or burns on the spouts. ■ Place the machine out of the reach of children. ■ Do not touch any hot parts. Use the handles provided. ■Be careful to ensure that the dual spout is correctly installed and clean. If it is incorrectly fitted or becomes blocked, its parts might come off. There is a danger of parts being swallowed. A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire: ■ Never allow the mains cable to loosely hang down. The mains cable could pose a tripping hazard or...

1 Preparing and using for the first time U Keep children under the age of 8 away from the machine, or supervise them constantly. U Children aged 8 and over may only operate the machine without supervision if they have been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use. People, including children, who U do not have the physical, sensory or mental capabilities to use the machine safely or U are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when...

1 Preparing and using for the first time Determining the water hardness When you use the machine for the first time, you must set the water hardness. If you do not know the hardness of your water, you can find this out first. Use the Aquadur® test strips supplied with the machine. ► Hold the test strip briefly (for 1 second) under flowing water. Shake off the water. ► Wait for about 1 minute. ► You will then be able to read the degree of water hardness from the discolouration of the Aquadur® test strip and the description on the packaging. J WARNING If the machine is operated with a...

1 Preparing and using for the first time T Insert the filter cartridge with its extension into the water tank. T Remove the protective cover from the dual spout. T Fill the water tank with fresh, cold water and reinsert the tank. T Connect the milk pipe to the dual spout. E The machine automatically detects that you have just inserted the filter cartridge. ‘Saved’ ‘Filter is being rinsed’, the filter is rinsed. Water flows directly into the drip tray. E If the ‘Empty drip tray’ message appears, empty the drip tray and put it back into the machine. ‘System is filling’ ‘Machine is heating’...

► Press the ‘Machine settings' button. ► Press the ‘ ► ' button several times until page ‘4/5' is displayed. ► Press the ‘Connect accessory' button. ‘Connect accessory' ► Now follow the instructions on the display to connect the accessory to the ENA. 2 Preparation Basic information about preparing drinks: ■ During the grinding operation you can change the coffee strength by pressing the ‘ < ' and ‘ > ' buttons. ■ During preparation you can change the preset amounts (e.g. water and amount of milk foam) by pressing the ‘ < ' and ‘ > ' buttons. ■ If you have selected settings during...

► Press the ‘Latte macchiato' button. ‘Latte macchiato', the preset amount of milk foam flows into the glass. i There is a short interval while the hot milk separates from the milk foam. This allows the typical layers of a latte macchiato to form. Coffee preparation starts. The preset amount of water for espresso flows into the glass. Preparation stops automatically. Your ENA is once more ready for use. i 15 minutes after preparation, the milk system is automatically rinsed (see Chapter 5 ‘Maintenance - Automatic milk system rinsing'). Therefore always place a receptacle under the dual...

Adjusting the grinder You can adjust the grinder to suit the degree of roast of your coffee. CAUTION If you adjust the consistency of grind when the grinder is not operating, the grinding wheel could be damaged. ► Only adjust the consistency of grind when the grinder is running. The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms. Grinding wheel (see image) ■ 1: Coarse consistency of grind setting ■ 2: Fine consistency of grind setting J CAUTION There is a danger of scalding from hot water splashes. ► Avoid...