868 SLH SYSTEM
1 / 3ページ

{{requestButtons}}

カタログの抜粋

868 SLH SYSTEM - 1

FAAC S.p.A. Via Benini,1 • 40069 Zola Predosa, Bologna S 051-61724 S 051-758518 B www.faacgroup.com 868 SLH SYSTEM The 868 SLH Series is a patented 868 Mhz radio-control system with encrypted self-learning Rolling Code. At every transmission, the transmitter code changes according to a complex algorithm, synchronised with data awaited by the receiver. TECHNICAL SPECIFICATIONS * External factors such as atmospheric disturbances, within-range obstacles, and charge level of transmitter batteries, can affect nominal capacity (significantly in some cases). 868 SLH TRANSMITTERS The transmitters (2/4 channel) can be of two types: master and slave. How to recognise a master/slave transmitter •master: if you press any key of a master TX, the LED flashes before becoming steady •slave : if you press any key of a slave TX, the LED goes on immediately with steady light. Differences between master and slave TX •master: only a master TX can transfer its "system code" to decoding cards/RP receivers and to other TXs (master or slave). •slave: unable to transfer its "system code" and, therefore, cannot be either duplicated, or used for coding systems. Can learn the "system code" from a master TX.

カタログの1ページ目を開く
868 SLH SYSTEM - 2

a radio receiver for connection to one or more decoding cards (one decoding card for each channel). •RP 868 SLH: single-channel radio receiver with built-in decoding facility, and rapid connector for connection to FAAC equipment. Stores up to 250 TXs. 868 DECODING CARDS •SLH Minidec: decoding card with open-collector output and rapid connector for connection to FAAC equipment. Stores up to 250 TXs. •SLH Decoder: decoding card with relay output and rapid connector to connection to FAAC equipment, plus terminal board for wired connection. Stores up to 1000 TXs. OPERATION DESCRIPTION The 868...

カタログの2ページ目を開く
868 SLH SYSTEM - 3

• On the master TX (while its LED is flashing), press and hold down the same channel used for coding the system: the LED goes on with steady light; • Press the required channel on the TX to be coded and release it when the LED goes off after flashing twice to confirm the “system code” was saved; • Release the button of the Master TX channel; • Repeat this procedure for every TX to be coded. CONVERTING A TX FROM MASTER TO SLAVE Procedure for converting a master transmitter into a slave transmitter: • Simultaneously press push-buttons P1 and P2 of the master TX and release them when the LED...

カタログの3ページ目を開く

FAACのすべてのカタログと技術パンフレット

  1. 620

    2 ページ

  2. XTR B TAG Reader

    4 ページ

  3. TK20

    6 ページ

  4. A1400 AIR

    8 ページ

  5. 640

    2 ページ

  6. B614

    4 ページ

  7. 746

    2 ページ

  8. S418

    4 ページ

  9. VIPER 400

    6 ページ

  10. TAG - 10

    2 ページ

  11. Resist T-PS-TPS

    1 ページ

  12. J Series Bollards

    32 ページ

  13. S800 ENC

    4 ページ

  14. S800H ENC

    4 ページ

  15. S450H

    2 ページ

  16. REVOLVING DOORS

    9 ページ

  17. C720

    2 ページ

  18. 740 - 741

    2 ページ

  19. 750 operator

    2 ページ

  20. J200 Series bollard

    13 ページ

  21. 770N 24V operator

    2 ページ

  22. XT 868 (new)

    2 ページ

  23. BOLLARDS

    8 ページ

  24. S700 operator

    9 ページ

カタログアーカイブ

  1. Gearmotor C720 24V

    4 ページ

  2. Transmitters XT

    4 ページ

  3. T- Mode

    8 ページ