MISTRAL
1 / 36ページ

KEEP THIS MANUAL FOR FUTURE NEEDS

7. DMX-512 CONNECTION WITH DMX TERMINATOR 13 8. DEVICE DMX START ADDRESS SELECTION 14

This device has left the factory in perfect condition. In order to maintain this condition and to ensure safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. In order to install, operate, and maintain the lighting fixture safely and correctly we suggest that the installation and operation be carried out by qualified technicians and these instructions be carefully followed. CAUTION! HIGH VOLTAGE. RISK OF SEVERE OR FATAL ELECTRIC SHOCK CAUTION! ALWAYS DISCONNECT MAINS SUPPLY BEFORE REMOVING ANY FIXTURE COVERS...

replaced by the manufacturer or their service agent or a similar qualified person in order to avoid injury. • When the device is not in use or before performing maintenance, always disconnect the device from the mains. Only handle the power cord from the plug .Never pull the plug out of a socket by tugging the power cord. • When powered on for the first time, some smoke or smell may occur. This is caused by coating on metal parts when heated and is normal.If you are concerned, please contact your distributor. • Do not focus the beam onto flammable surfaces. The minimum distance between the...

• Power Consumption: 550W LIGHT SOURCE • LED: White LED 330W 7000K± 450K Color Temperature @ MISTRAL TC White LED 330W 8000 ± 500K Color Temperature @ MISTRAL S • Extremely long Life: >50,000H MOVEMENT • Pan movement: 540° /630°Optional (16 bit) • Tilt movement: 270° (16 bit) • Advanced moving system: fast, stable and quite, auto x-y repositioning COLORS • CMY color mixing + CTO • 1 Color wheel: 7 dichroic filters + open, indexable, rainbow effect GOBOS • Rotating gobo wheel: 7 interchangeable, rotating, and indexable, gobo+open • ” Slot in & out ” gobo wheel system • Fix gobo wheel: 9 +...

OTHER SPEC Input signal isolation guarantees stable signal transmission without interference Advanced RDM function WEIGHT Net weight: 19 kg DMX CHANNELCHART

1) LED Assembly 2) Display 3) Rotary knob 4) Handle 5) Lock button

4. DIMENSIONAL DRAWINGS 4.1. Fixture Dimension

Color Gobo

A PLEASE CONSIDER THE RESPECTIVE NATIONAL NORMS DURINGINSTALLATION. THE INSTALLATION MUST ONLY BE CARRIED _OUT BY A QUALIFIED PERSON._ • The applicable temperature for the lighting is between -10°C to 45°C. Do not use the lighting under or above the temperature. • The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. • The installation must always be secured with a secondary safety attachment, e.g.an appropriate safety rope. • Never stand directly below the device when mounting, removing or...

5.2. Rigging using the omega brackets Fix the clamp to the bracket by tightening the M12 nut and boltto the bracket through the 13 hole in the middle of the bracket. Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the device.Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder. Pull the safety cable through the holes on the bottom of the base and over the trussing system or another suitable rigging point. Insert the end into the carabiner and tighten the safety screw. Important This step is very important to...

• Be sure this fixture is kept at least 0.1m away from any flammable materials (decoration etc.). • Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Kg3Important: Overhead rigging requires extensive experience , including (but not limited to) calculatingworking load limits, specifying installation/ rigging materials, and periodic safety inspection of all installation material as well as the device .If you lack these qualifications, do not attempt therigging of this device yourself. Improper...

6. DMX-512 CONTROL CONNECTION Connect the provided male side of the XLR cable to the femaleXLR output of your controller and the female side of the XLR cable to the male XLR input of the device.You can connect multipledevices together in a serial fashion.The cable needed should be two core screened cable with XLR input and output connectors.Please refer to the diagram below. 7. DMX-512 CONNECTION WITH DMX TERMINATOR For installations where the DMX cable has to run over a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX...

8. DEVICE DMX START ADDRESS SELECTION All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals.This digital starting address is the channel number from which the fixture starts to listen” the digital control information sent out from the “ to DMX controller.The allocation of this starting address is achieved by setting the correct address number on the display located on the base of the device. You can set the same starting address for all fixtures or a group of fixtures addresses for each fixture...

9.1.1. Set DMX Address With this function, you can adjust the desired DMX-address via the Display. 1. Double click to enter the menu. 2. The display will show " ADDRESS ”. 3. Double click to enter then display " Set DMX Address ”. 4. Turn the rotary knob clockwise then display " A001~AXXX ”. 5. Long press to exit the menu. 9.2.1. User Mode With this function, you can create user defined channel orders. 1. Double click to enter the menu, turn the rotary knob clockwise to display " USERS MODE ” . 2. Double click to enter to edit. 3. Turn the rotary knob clockwise to display " User mode ”...

or close the shutter or run an automatic sequence. The default is hold. 1. Double click to enter the menu. 2. Turn the rotary knob clockwise then display " Options ”. 3. Double click to enter " Options”, turn the rotary knob to select " Status ”. 4. Double click to enter " Status ” menu, The display will show " No DMX Status ”. 5. Double click to enter " No DMX Status”, The display will show " Hold”, Turn the rotary knob to select " Close ” or " Auto ” 6. Long press to exit the menu. Pan Reverse With this function you can reverse the Pan-movement. 1. Double click to enter the menu. 2. Turn...