カタログの抜粋

ROOFING PRODUCTS MASONRY TO STEEL WALL TIES Marking Featuring onstruction to the C ulation Products Reg OTHER MASONRY PRODUCTS MASONRY TO TIMBER WALL TIES Wall Ties & Restraint Fixings WALL STARTER SYSTEMS MASONRY TO MASONRY WALL TIES
カタログの1ページ目を開く
Logo Guide Look out for these logos. These products are supplied with a CE marking. This demonstrates compliance with a European Standard and is a legal requirement of the Construction Products Regulation from 1st July 2013. For more information and to download all associated documents, including Declarations of Performance, go to www.ancon.co.uk/CE. These products are approved by the British Board of Agrément. These products meet the technical requirements of the National House Building Council. These products are Type A ties and suitable for internal separating walls to Approved Document...
カタログの2ページ目を開く
Staifix Timber Frame Tie Staifix-Thor Helical Timber Tie Ancon Teplo-L-Tie Staifix Frame Tie Masonry to Steel Wall Ties Ancon 25/14 Restraint System Other Masonry Products Ancon AMR and AMR-X Masonry Reinforcement Staifix Insulated Plasterboard Nails Staifix-Thor Helical Crack Stitching Kit Remedial Wall Ties Roofing Products Wire Balloons Super-7 Thor-Helical Nail for Pitched Roofs Super-8 Headed Helical Nail for Flat Roofs MASONRY TO STEEL WALL TIES Masonry to Timber Wall Ties MASONRY TO TIMBER WALL TIES WALL STARTER SYSTEMS Staifix Universal Wall Starter System Staifix QuickStart Wall...
カタログの3ページ目を開く
Stainless Steel Cavity Wall Ties for traditional masonry construction with cavities from 50mm to 175mm Staifix Universal Insulation Retaining Clip For use with standard Staifix stainless steel ties in partial fill cavities Application These stainless steel wall ties connect the two leaves of a cavity wall. Product selection is based on building type and height, geographical location and cavity width. Specially designed safety ends reduce the risk of injury during handling and installation. e: Now availabl l Tie product Wal selector App
カタログの4ページ目を開く
MASONRY TO MASONRY WALL TIES Staifix HRT4 Light Duty Tie (Type 4 Tie to PD6697/Type A Tie to Approved Document E) Length (mm) 200 225 250 275 Type 4 wall tie for use in the external walls of houses up to 10 metres in height. Altitude and wind speed restrictions may apply. Type A tie suitable for internal separating walls of buildings of any height. Staifix RT2 General Purpose Tie (Type 2 Tie to PD6697) Length (mm) 200 225 250 275 Type 2 wall tie for use in the external walls of houses and small commercial developments up to 15 metres in height. Altitude and wind speed restrictions may...
カタログの5ページ目を開く
Ancon TeploTie Basalt Fibre Wall Ties for ultra energy-efficient buildings with cavities up to 450mm Application The Ancon TeploTie is manufactured from pultruded basalt fibres set in an epoxy resin. It has a thermal conductivity of only 0.7W/mK which can be shown in U-value calculations to reduce insulation thickness and wall footprint. Teplo-Clip Insulation retaining clip for use with all Ancon TeploTies A sand finish llent provides exce tar key mor
カタログの6ページ目を開く
Type 4 wall tie for use in external walls of houses up to 10 metres in height. Altitude and wind speed restrictions may apply. Type 3 wall tie for use in external walls of houses and small commercial developments up to 15 metres in height. Altitude and wind speed restrictions may apply. Type 2 wall tie for use in external walls of houses and small commercial developments up to 15 metres in height. Altitude and wind speed restrictions may apply. Type 1 wall tie for use in the external walls of buildings up to 18m in height. Note: These ties are unsuitable for internal separating walls to...
カタログの7ページ目を開く
Staifix-Thor Helical TJ2 Tie for thin-joint blockwork Application Hammer-driven cavity wall tie, ideal for thin-joint blockwork and other applications where the joints of the inner and outer leaves of masonry do not course. Suitable for buildings up to 15 metres in height when used with high strength blocks. Contact Ancon for more details. For thin-joint to thin-joint separating walls use the Staifix HRT4 (see page 5). Hammers directly into ks Aircrete bloc
カタログの8ページ目を開く
Keep the brickwork one course clear during installation of the ties. Position the tie against the inner leaf so that the outer end will be located in the bed joint of the external leaf. Hammer the tie, through the insulation, and into the blockwork to the correct embedment. Support tools are available to simplify installation. Install a black Staifix TJ Insulation Retaining Clip to restrain the insulation. Build into the bed joint of the outer leaf ensuring the tie is surrounded by mortar. 85mm Embedment Staifix-Thor Helical TJ2 Thin-Joint Ties should have a minimum embedment of 85mm in the...
カタログの9ページ目を開く
Other Standard Ancon Wall Ties lengths shown in red italics refer to items available within 24 hours Ancon Teplo-L-Tie Low thermal conductivity restraint fixing For vertical movement joints Application Basalt fibre frame cramp with stainless steel upstand, used to join masonry to existing structures. Application Flat tie used with a debonding sleeve to allow the masonry to expand or contract. Lengths 150**, 200*, 225*, 250**, 300mm** *Conforms to PD6697 as a Type 2 tie **Type 3 tie Lengths 250, 275mm Conforms to PD6697 as a Type 3 tie Lengths 200, 225, 250, 275, 300mm Conforms to PD6697 as...
カタログの10ページ目を開く
For walls in which both leaves are 90mm or thicker, ties should be installed at not less than 2.5 square metre (900mm x 450mm vertical centres). Wall ties should be pressed down in, and then surrounded by, fresh mortar. To ensure cavity wall ties are effective at tying the leaves together they should be installed as the inner leaf is constructed and not simply pushed into a joint. Ties should be installed with a slight fall to the outer leaf, never towards the inner leaf as this could provide a path for moisture to cross the cavity. The drip part of the tie should point downwards and be...
カタログの11ページ目を開く
Staifix Wall Starter Systems for joining new walls to existing masonry Application Wall starters include all the necessary fixings (ties, plugs and screws) to join a single skin of masonry 2.4 metres high to an existing wall. Universal Wall Starter System Wall ties slide within the fixing strip to course with the bed joints of any masonry unit. Ideal for s, conservatorie tensions and ex garden walls QuickStart Wall Starter System Wall ties are integral to the stainless steel starter strip and fold out at pre-set 225mm vertical centres. Turn Slide
カタログの12ページ目を開くAncon Building Productsのすべてのカタログと技術パンフレット
-
Eazistrip
16 ページ
-
Tapered Thread Couplers
12 ページ
-
Reinforcing Bar Couplers
28 ページ
-
Restraint System
4 ページ
-
Ancon Thermal Breaks
2 ページ
-
Gauge Tape
2 ページ
-
Non-Drill Wall Ties
6 ページ
-
Refractory Fixings
8 ページ
-
Staifix Wall Ties
2 ページ
-
Special Fabrications
12 ページ
-
Starter Bar Systems
8 ページ
-
KSN Anchors
24 ページ
-
Lockable Dowels
12 ページ
-
Masonry Reinforcement
16 ページ
-
Corner Guards
2 ページ
-
Hidden Strength
7 ページ
-
12 Page Product Guide
12 ページ
カタログアーカイブ
-
Channel and Bolt Fixings
20 ページ