Installation guide KNX sensors
39Pages

{{requestButtons}}

Catalog excerpts

Installation guide KNX sensors - 1

Answers for infrastructure and cities. Mounting guidelines Commissioning assistant

Open the catalog to page 1
Installation guide KNX sensors - 2

Optimum control requires accurate measurements A control operation is only as good as the measuring accuracy of the sensors which detect the control variable (temperature, humidity, pressure, etc.) and transmit it to the controller as an actual value. While this process hasn’t changed, the measuring technology and methods for mounting sensors are more cutting-edge than ever before. Legal regulations increasingly appeal for the economic use of energy. At the same time, the indoor climate must meet stringent requirements. Both requirements can be fully met only if all necessary measured data...

Open the catalog to page 2
Installation guide KNX sensors - 3

Future-proof building control Everything you need for a good working climate Working concentrated while saving energy – products from Siemens improve the atmosphere in rooms and facilitate more economical operations. The result: perfectly temperature-controlled and air-conditioned rooms with good lighting and reduced energy consumption. Mounting guidelines up to 30 percent energy with individual room control and energy saving functions ■ ■ rotects investments on the basis of reliable products and P the ability to add third-party devices via KNX ■ ■ asy commissioning and adaptation to...

Open the catalog to page 3
Installation guide KNX sensors - 4

Contents Mounting guidelines for sensors Commissioning assistant Outdoor temperature sensors Commissioning a KNX/Ethernet system (LAN) Motion detectors Commissioning a KNX/Ethernet system (WLAN) Presence detectors (incl. brightness sensors) Coupling KNX lines via Ethernet (LAN) Room sensors for temperature, humidity and air quality Remote access to KNX via the Internet (DSL) Outdoor brightness sensors Wind sensors Monitoring properties with KNX via Ethernet (LAN) Door/window contacts Using DALI luminaires with easy KNX commissioning Weather stations/sensors (sun, wind, rain) Wireless remote...

Open the catalog to page 4
Installation guide KNX sensors - 5

Mounting guidelines for sensors O utdoor temperature sensors • otion detectors M • resence detectors (incl. brightness sensors) P • oom sensors for temperature, humidity and air quality R • utdoor brightness sensors O • ind sensors W • oor/window contacts D • eather stations/sensors (sun, wind, rain) W • Mounting guidelines Contents Outdoor temperature sensors Motion detectors Presence detectors Bus systems Room sensors Outdoor brightness sensors Commissioning assistant Wind sensors Glossary Door/window contacts Weather stations/ sensors

Open the catalog to page 5
Installation guide KNX sensors - 6

Outdoor temperature sensors Depending on the application, place outdoor temperature sensors as follows: For control The sensors should be mounted on the outer walls with the windows of the main living areas. However, they should not be exposed to morning sunlight. In case of doubt, you can mount these sensors on the north or northwest wall. For optimization not expose to direct sunlight ■ ■ Do not mount on facades with a great deal of ascending heat ■ ■ Do not attach to walls in front of a chimney ■ ■ Do not mount on eaves or a balcony ■ ■ Do not place over windows ■ ■ Do no mount over...

Open the catalog to page 6
Installation guide KNX sensors - 7

Motion detectors Mounting guidelines for motion detectors in a room Mounting guidelines for motion detectors on a building not expose motion detectors to direct sunlight ■ ■ ake sure that the sensors cannot be affected by air M turbulences, e.g., do not install them near fan heaters ■ ■ luorescent and incandescent lamps in the detection zone F must be placed at least 1 ‒ 3 meters away from the sensor ■ ■ ount the motion detector laterally to the direction of M walking Mounting guidelines Contents Outdoor temperature sensors Motion detectors Presence detectors not expose motion detectors to...

Open the catalog to page 7
Installation guide KNX sensors - 8

Presence detectors (incl. brightness sensors) Mounting guidelines for presence detectors ■ ■ ake M sure that the workplace is right in the detection zone of the presence detector – without any obstacles such as shelves, plants, glass walls, etc. blocking the detector ■ ■ eep in mind that moving machines, plants and animals in K the detection zone will be interpreted as movement ■ ■ void sources of rapid changes in temperature or light, such A as fans, incandescent or halogen lamps; air flows and light in the detection zone simulate movement ■ ■ ount at least 50 cm away from cables and...

Open the catalog to page 8
Installation guide KNX sensors - 9

Room sensors for temperature, humidity and air quality To ensure accurate readings, it is a good idea to keep the following in mind during installation: When mounting on massive walls (1) made of steel, concrete, etc., you need to place thermal insulation (2) between the room sensor (3) and the wall. 1 Mounting guidelines for room sensors Clearances between the cable (4) or plastic hose and the installation pipe (5) need to be sealed. Otherwise, inefficient air circulation will occur, causing measuring errors. room sensors in the living area at a height of approx.1.5 meters and a distance...

Open the catalog to page 9
Installation guide KNX sensors - 10

Outdoor brightness sensors Mounting guidelines for outdoor brightness sensors ■ ■ hen W selecting the mounting site, consider the part of the building (heating zone) for which the outdoor brightness sensor is to detect the incident sunlight; attach the sensor to the wall that contains the windows of the rooms to be affected ■ ■ ount sensors in an accessible location (so they can M be checked) ■ ■ Avoid shade due to trees, neighboring houses, etc. ■ ■ Never paint over sensors ■ ■ Mount the sensor at least 3 m from the ground ■ ■ Mount the sensor at least 0.3 m from the window Mounting...

Open the catalog to page 10
Installation guide KNX sensors - 11

Wind sensors Mounting guidelines for wind sensors ■ ■ Mount on the facade with the main wind direction a site on the building where the sensor can detect the wind unhindered ■ ■ ount sensors in an accessible location (so they can M be checked) ■ ■ Do not mount under eaves or balconies ■ ■ Do not place in alcoves ■ ■ Consider interference factors such as trees, shrubs and snow ■ ■ Best mounted on a pole ■ ■ Mount the sensor at least 60 cm from interference factors ■ ■ elect S Main wind direction Mounting guidelines Contents Outdoor temperature sensors Motion detectors Presence detectors Bus...

Open the catalog to page 11

All SIEMENS Building Automation and Control catalogs and technical brochures

  1. RDS110

    22 Pages

  2. PXC5.E003

    12 Pages

  3. PXC4.M16

    16 Pages

  4. QAF63.2-J

    8 Pages

  5. PXM30-1

    10 Pages

  6. PXC4.E16

    14 Pages

  7. A6V10575277

    16 Pages

  8. Gamma instabus

    14 Pages

  9. RRV934

    12 Pages

  10. WRI982

    12 Pages

  11. Catalog LV 51

    150 Pages

Archived catalogs