Catalogs >
SCHAKO KG >
BKP-EN

BKP-EN
40Pages

Catalog excerpts

Technical Documentation "Installation, Mounting and Operating Instructions" BKP-EN Fire damper Fig.: BKA-EN with B10 drive USABILITY CERTIFICATES PERFORMANCE DATA • Performance Reliability Certificate according to EU-Bau PVO 0761 - CPR - 0350 • Declaration of Performance 09-23-DoP-BKP-EN-2013-11-01 • For automatic locking of fire lobbies • For use or connection of a smoke release device with abZ (e.g. SCHAKO smoke detection system RMS) in connection with suitable release devices (e.g. spring return actuator) • Classification according to EN 13501-3, depending on the mounting situation EI 90(120) (ve, ho iOo) S • Product standard EN 15650 • Test standard EN 1366-2 ATEX version available (at an extra charge) Extensive uses and applications Large free cross-sections For optimum integration into the building control system via the SCHAKO EasyBus signalling and switching bus system or the SCHAKO BKSYS fire damper mini-controller SCHAKO | Ferdinand Schad KG Phone +49 (0) 7463-980-0 D-78600 Kolbingen www.SCHAKO.de | info@SCHAKO.de

Open the catalog to page 1

Fire Damper Model BKP-EN Technical documentation Table of Contents Construction subject to change. No return possible!

Open the catalog to page 2

Fire Damper Model BKP-EN Technical documentation Description DESCRIPTION Fire dampers built into ventilation ducts (air-conditioning systems) are used for the automatic locking of fire lobbies. The fire damper BKP-EN conforms to EN 15650, EN 13501-3 and EN 1366-2. The BKP-EN has been tested according to EN 1366-2 in compliance with Declaration of Performance no. 09-23-DoP-BKPEN-2013-11-01. It has the Performance Reliability Certificate according to EU-Bau PVO 0761-CPR-0350. Its category according to EN 13501-3 is depending on the mounting situation EI 90(120) (ve, ho i↔o) S. According to...

Open the catalog to page 3

Fire Damper Model BKP-EN Technical documentation Models and dimensions MODELS AND DIMENSIONSDimensions 1 Housing 2 Damper blade 3 Hand lever 4 Locking profile 5 Trigger device 6 Fusible link 7 Inspection opening (arranged at bottom) from B > 200, for B < 200 no inspection opening possible. x = B/2 200 > B < 600 or x ~ 125 mm ^ B > 600 y ~ 100 mm from the connection flange 8 Drive unit 9 Profile CW 50/50/0.6 (with wall thickness = 100 mm, for larger wall thicknesses, the profiles must be adapted accordingly). 10 Profile UW 50/40/0.6 (with wall thickness = 100 mm, for larger wall thicknesses,...

Open the catalog to page 4

Fire Damper Model BKP-EN Technical documentation Models and dimensions • Housing length L = 330 mm. • All heights and widths which can be combined are available! • Trigger device always on H side • Inspection opening always on B side (bottom) • Intermediate sizes on request "a" = 50 mm: Minimum distance between the front edge of the open damper blade and the finishing protective grating (ASG), the flexible spigot (FS) or the duct connection spigot (RS). SCHAKO ASG/VT/FS/RS: Flange holes suitable for The fire damper type BKP-EN is supplied with front side fitted corner long holes for M8...

Open the catalog to page 5

Fire Damper Model BKP-EN Technical documentation Models and dimensions Use be exposed to direct effects of the weather and must not be stored below -40 °C or above 50 °C. The fire damper type BKP-EN can be fitted as shown in the following table. The BKP-EN may also be installed in walls or ceilings of a lower fire resistance class. In this case, the BKP-EN has the same fire resistance class as the wall or ceiling. 1) Installation only in connection with a concrete base still to be made on site. Tab. 3: Usability • During mounting or installation, there is a risk of injuries. To avoid any...

Open the catalog to page 6

Fire Damper Model BKP-EN Technical documentation Installation details INSTALLATION DETAILS Installation positions Installation in solid walls  Installation in solid walls (shaft walls, shafts, ducts and fire walls) made of, for example, concrete, masonry according to EN 1996 or DIN 1053; solid plaster wall boards according to EN 12859 or DIN 18163; apparent density ≥ 450 kg/m³ and wall thickness W ≥ 100 mm.  On the non-operating side, fastening materials (e.g. screws, press-in nuts, etc.) must be provided for mounting duct components prior to installation of the BKP-EN. Alternatively,...

Open the catalog to page 7

Fire Damper Model BKP-EN Technical documentation Installation details Installation in solid ceilings  Installation in solid ceilings made, for example, of concrete, aerated concrete, apparent density ≥ 500 kg/m³ and ceiling thickness D ≥ 125 mm.  On the non-operating side, fastening materials (e.g. screws, press-in nuts, etc.) must be provided for mounting duct components prior to installation of the BKP-EN. Alternatively, extension pieces (on site or as accessories, e.g. SCHAKO type VT) can be mounted.  Installation with complete mortar lining (the circumferential gaps "s" must be...

Open the catalog to page 8

Fire Damper Model BKP-EN Technical documentation Installation details Installation with vertical concrete base on solid ceilings  Vertical installation on solid ceilings made, for example, of concrete, aerated concrete, apparent density ≥ 500 kg/m³ and ceiling thickness D ≥ 125 mm. Construction of a circumferential, straight reinforced concrete base (concrete grade: C20/25; concrete cover ≥ 35 mm; reinforcement: concrete steel BSt500S concrete steel mats B500A). The base must be constructed circumferentially with a wall thickness of at least 100 mm, measured from the housing of the fire...

Open the catalog to page 9

Fire Damper Model BKP-EN Technical documentation Installation details Installation in lightweight partition walls with metal posts and panelling on both sides  Installation in lightweight partition walls with metal posts and panelling on both sides (gypsum-bonded wall boards; wall thickness W≥ 100 mm) as classified according to EN 13501-2 or comparable national standards.  On the non-operating side, fastening materials (e.g. screws, press-in nuts, etc.) must be provided for mounting duct components prior to installation of the BKP-EN. Alternatively, extension pieces (on site or as...

Open the catalog to page 10

BKP-EN 40Pages

Catalog excerpts

All SCHAKO KG catalogs and technical brochures

BKP-EN
40Pages