Group: Ronacrete Limited
Catalog excerpts
RonaBond EasySkim FC Polymer modified, pre-packed fairing coat FEATURES pre-packed fairing coat apply prior to application of surface coating 1mm - 3mm application thickness fair-faced finish on walls and soffits apply by trowel covers minor blemishes RonaBond EasySkim FC is a pre-packed fairing coat mortar which is applied as a skim coat in thicknesses up to 3mm to provide a smooth, hard finish to damaged, blemished and repaired concrete surfaces. RonaBond EasySkim FC is used as a levelling mortar prior to the application of protective coatings or paints. The material is supplied in pre-blended form. Physical Properties Pack size Packs per m3 Yield per pack Coverage per pack Min/max application depth per layer Initial set (approximately) Final set (approximately) Preparation Careful preparation of the substrate is required before application. The substrate must be clean, sound and free of dust, algae, laitance and deleterious material. Surfaces must be sufficiently stable, sound and strong to receive the RonaBond EasySkim FC. Surfaces should be repaired or made good as required. Fill large blemishes greater than 3mm deep using RonaBond Concrete Repair Mortar or RonaBond HB40 to prevent them showing through the finished RonaBond EasySkim FC. Damp the prepared surface with clean water and remove any excess. Mixing Mix using a slow speed drill fitted with a suitable paddle attachment or a forced Concrete Repair and Coatings Continued on following page... Other Ranges—Resin Bound and Bonded Surfacing, Screeds, Flooring and Bedding, and Waterproofing and Tanking
Open the catalog to page 1RonaBond EasySkim FC Polymer modified, pre-packed fairing coat Instructions for Use (continued) action mixer; do not use a free fall mixer. Pour approximately two thirds of the gauging liquid into the mixing vessel and gradually add the powder component. Mix for 2 minutes and add sufficient of the remaining gauging liquid to achieve the desired consistency. Mix for a further 1 minute. Application Tight trowel the mixed material to the damp surface ensuring total contact. The surface can be textured using a damp sponge. This must be carried out before the material hardens. Application in...
Open the catalog to page 2RonaBond EasySkim FC Polymer modified, pre-packed fairing coat Technical and Test Data Note that all quoted data is based on laboratory tests conducted at 20 oC. Cubes, tested at 28 days, are 100mm and air cured. Results shown are MAXIMUM laboratory strengths achieved by casting and curing cubes in ideal working conditions; site strengths will be lower. Site Attendance When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an...
Open the catalog to page 3RonaBond EasySkim FC Polymer modified, pre-packed fairing coat 0836 Ronacrete Ltd, Flex Meadow, Harlow Essex, CM19 5TD, UK 13 0836-CPR-13/F045 BS EN 1504-2 Concrete Repair Surface Protection System Product: RonaBond EasySkim FC Capillary abs. & perm. to water: W < 0.1kg/m2 .h0.5 Reaction to Fire: Euroclass F Dangerous Substances: Refer to Safety Data Sheet The information detailed in this leaflet is liable to modification from time to time in the light of experience and of normal product application, and before using, customers are advised to check with Ronacrete Ltd, quoting the reference...
Open the catalog to page 4All Ronacrete Limited catalogs and technical brochures
-
RonaDeck EcoPath MT
4 Pages
-
RonaDeck Eco Tree Pit
4 Pages
-
Ronacrete Curing Membrane
2 Pages
-
RonaBond Re-Profiling Mortar
4 Pages
-
RonaBond FC for Prison Cells
4 Pages
-
RonaBond Concrete Cover 150
3 Pages
-
Monoprufe WP Elastic
4 Pages
-
RonaBond Bedding Mortar
4 Pages
-
Ronafix for Renders
4 Pages
-
Monoprufe DPM
3 Pages
-
RonaBond Slurry Coat
3 Pages
-
RonaBond MCI
3 Pages
-
RonaBond Masonry Coating WB
3 Pages
-
RonaBond HB25
4 Pages