|
Stand
|
dream series - 11 Pages
Dream Series Control
Initial Start Up
When your spa is first powered up, it will go into Priming Mode, indicated by ՓPr. Priming mode will last for 5 minutes and then the spa will being to heat the spa and maintain water temperature in the Standard Mode. During this cycle do not press any buttons as it will cause the priming mode to start over. >
Temperature Control Light
The start-up temperature is set at 100ԺF. The last measured temperature is constantly displayed on the LCD. Note that the last measured spa temperature displayed is current only when the pump has been running for at least two minutes. Press the TempӔ button to display the temperature previously set. This set temperature is flashed on the display. Pressing the TempӔ button a second time, while it is still flashing, will cause the set temperature to increase or decrease depending on what direction was last chosen. Each press to follow will change the set temperature in the same directions. If the opposite direction is desired, release the pad and let the display revert to the actual water temperature. Press the button to display the set temperature, and again to make the temperature change in the desired direction. Press the LightӔ button to turn the light on and off. If left on, the light automatically turns off after four hours. >
Preset Filter Cycles
The first filter cycle begins six minutes after the spa is energized. The second filter cycle begins 12 hours later. Filter duration is programmable at the Master Control Pad for 2, 4, 6, 8 hours or for continuous filtration, (indicated by FCӔ). The default filter time is two hours. To program, press TempӔ, then Jets.Ӕ Press TempӔ to adjust. Press JetsӔ to exit programming. >
Freeze Protection
If the temperature sensors detect a drop below 40F within the heater, then the pump (as well as the heater, if necessary) will automatically activate to provide freeze protection. The equipment stays on until the sensors detect that the spa temperature has risen to within 15ںF of the set temperature. The blower will purge for 30 seconds at the end of the freeze condition.
Jets
Touch the JetsӔ button once to activate the low speed of the pump and again for the high speed. Press the JetsӔ button again to turn off the pump. If left running, the pumps low speed will automatically turn off after four hours, and the pumpҒs high speed will automatically turn off after 15 minutes. The low speed of the pump runs when the blower is on. It may also activate for at least two minutes every 30 minutes to detect the spa temperature and then to heat to the set temperature if needed, depending upon mode. When the low speed turns on automatically, it cannot be deactivated from the panel; however, the high speed may be started. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instruction, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a class B computing device in accordance with the specification in subpart J of part 15 of the FCC rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measurers: Reorient the receiving antenna. Relocate the receiver with respect to the spa. Move the receiver away from the spa. Plug the receiver into a different outlet so that the receiver and spa are ondifferent circuits. If necessary, the user may find the following booklet prepared by the Federal Communications Commission helpful: "How to identify and resolve radio-TV interference problems." This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-00000345-4. >
5 size="-1">
-
P. 1
ENJOY Your QCA Dream Series Spa >VS500 Spa Pak OWNERS MANUAL >This ownerҒs manual is for YOU! It will show you how to operate and maintain... -
P. 2
.TABLE OF CONTENTS Cleaning the Filter Cartridge............................................................................8 Diagnostic Messages.........................................................................................6... -
P. 3
UL INSTRUCTIONS The instructions that you are about to read, are required by Underwriters Laboratories to be published in your manual. These instructions... -
P. 4
Spa Location Installation Instructions The selection of a site for the installation of your spa is a very important decision and should be undertaken keeping... -
P. 5
-
P. 6
Diagnostic Messages Message Meaning Action Required No message on display. Power has been cut off to the Spa. The control panel will be disabled until... -
P. 7
QCA Spa Light All equipment Modules have a receptacle, located on the Equipment Module. This receptacle is provided for the connection of the spa light.... -
P. 8
The cartridge of the in-line filter must be removed for cleaning. This is accomplished as follows: for box filter 1.Remove filter lid. 2.Twist and lift... -
P. 9
Caution: Any lines not receiving adequate antifreeze are subject to freeze damage!Spa and Cabinet Maintenance Acrylic Finish - 3. Upon your return, check... -
P. 10
WARRANTY REGISTRATION This warranty applies to spas manufactured by QCA JEWEL Spas and sold to an original consumer purchaser at retail ("Purchaser") after...
