cad

ESCALIB MILLS KIT
20Pages

{{requestButtons}}

Catalog excerpts

ESCALIB MILLS KIT - 1

Site spiral stair tower with side exit (bolTed Module)... Mills provides you with solutions

Open the catalog to page 1
ESCALIB MILLS KIT - 2

Escalib Mills: spiral stair tower with side exit... he escalib is a metal spiral stair tower with a side exit. The triangular step acts as a landing. In order for the steps to be leveled with the desired floor, a 90° rotation or more might be necessary. The stair tower is composed of a base, with 1 to 8 modules that are easy to assemble with a crane and a barrier gate at the top (maximum height 20m10). The build which uses only collective protection (no safety harness) is simple and fast with only 4 screws per module. each module is fitted with fold-away guardrails that are attached at one...

Open the catalog to page 2
ESCALIB MILLS KIT - 3

The Escalib Mills stair tower has only 3 different unitary components. Description Weight is in kg. Up to 8 stacked modules: Heights are in meters Max. heigh modules x 2.50 m «(P) Max. height serviced » number of ESCALIB MILLS MDS KIT: SITE SPIRAL STAIR TOWER WITH SIDE EXIT (BOLTED MODULE)

Open the catalog to page 3
ESCALIB MILLS KIT - 4

All the module’s faces are secured by swivel guardrails. The triangular steps reaching into the corners (0.51 x 1.00 m) act as landings for resting and allowing users to pass. A sticker on the modules and bases indicates the orientation of the stair tower depending on the height required and gives instructions for erection, lifting, anchoring and transport. Access configurations at the level of the floor slab being serviced: bARRIeR GATe The barrier gate can be fitted to the module before delivery to the site. “ToPMoST” Module open access. Recommended. Closed access. Configurations for main...

Open the catalog to page 4
ESCALIB MILLS KIT - 5

> Erection guardrail in closed position: Gravity keeps the erection guardrail horizontal. It thereby enables safe slinging and safe fitting and removal of a module and barrier gate. Fitting or removing a module. Fitting or removing the barrier gate. > Erection guardrail in the open position: To let users pass, the erection guardrail swings upward and locks: - It is retained by a cable fixed to the module above - It is attached to the barrier gate when the exit is formed at the top level. NB: The erection guardrail must not be used as a substitute for the barrier gate. N.B.: during...

Open the catalog to page 5
ESCALIB MILLS KIT - 6

> 1 - The base must be oriented according to the height of the floor which needs to be accesed. Start the installation 8 cm away from the wall to facilitate pivoting of the guardrails at the access level. level the base. > 2 - Access inside the module is available for attaching the sling to the center ring, for putting the guardrails in closed position and putting the erection rails in horizontal position. > 3 - Fitting the module to the base. Assembly of the 4 uprights with M24 screws. Sling released. ASTUCE Example of an Escalib Mills with 3 modules Start bolting with the new module’s...

Open the catalog to page 6
ESCALIB MILLS KIT - 7

> 7 - With the slings attached to the 2 lifting rings, the topmost module is fitted. bolt the 4 uprights together using M24 screws. > 8 - Check that the stair tower has been anchored before unhooking the slings. Guardrails will be swung out of the way to allow access to the required level. > 6 - Fitting and bolting the barrier gate with M16x100 screw: the erection guardrail is positioned horizontally. The last step used should ideally be placed 21 cm lower than the floor being serviced. > 9 - At the access levels, the guardrails are positioned so as to privilege access by the main face A...

Open the catalog to page 7
ESCALIB MILLS KIT - 8

lifting and moving REQUIREMENTS: > Fit new anchorages as new modules are added. > The dismantle must be done in the reverse order of assembly. (no more than 8 modules stacked)... NB: Check that the ground on which the escalib Mills is to be erected is able to withstand the load. NB: Comply with the general rules for handling and stability. > 3 - Positionning on the ground and leveling the escalib. > 1 - Reposition the guardrails to close any side exits. Check that the M24 screws are tight in place. Attach the crane hooks to the 2 lifting rings. detach the anchors. > 2 - Move the escalib....

Open the catalog to page 8
ESCALIB MILLS KIT - 9

Configuration... Dimensions: Number of modules A* Add one module B* I to access the last 4 steps. The last step used should ideally be placed 21 cm lower than the floor being serviced. stacked. For taller stair towers, contact our design office. NB: 8 users per module, limited to 20 on a single, complete escalib Mills. N.B.: Check that the ground on which the escalib Mins is to be erected is able to withstand the load. | Example of Escalib Mills j The last 4 steps are only accessible when the upper module is fitted. With 2 modules, the height serviced i is limited to 5 m. '...

Open the catalog to page 9
ESCALIB MILLS KIT - 10

High performance and strength... o make it easier to size the anchor points and ground bearing for the escalib, the ground load calculations and the forces at the anchor points are given for the various configurations. Assumptions: I - Wind action as in EN 1991-1-4: - f = 0.23 and Cf = 2.73 - vp : Wind speed (km/h). - qp : Peak wind pressure (daN/m²). 2 - Working load Q: - 8 persons per Escalib Mills module. - Up to a maximum of 20 for the complete stair tower. - Stair tower not to be used for winds of over 65 km/h. 3 - Weight (P) of Escalib Mills. If “d” is greater than 20 cm, wind bracing...

Open the catalog to page 10
ESCALIB MILLS KIT - 11

Example: An 8-module Escalib located in Paris is subject to a peak wind pressure qp of 54 daN/m2, corresponding to a wind speed of 107 km/h. In configuration I, the Escalib is anchored every 3 modules. Each anchors must withstand the following stresses: - shearing: V = 300 daN, - pullout:T = 200 daN. NB :The holes drilled in the foot plates are to be used to nail through to wooden blocks when it is necessary to spread the load on the ground. They must not be used to anchor the Escalib Mills. ESCALIB MILLS MDS KIT: SITE SPIRAL STAIR TOWER WITH SIDE EXIT (BOLTED MODULE) "No entry" is...

Open the catalog to page 11
ESCALIB MILLS KIT - 12

escalib Mills KIT (bolTed Module)... olted escalib Mills modules are designed to be easily transported in a container. When assembled, they are the same shape as the welded modules and are fully compatible. The uprights, stringers and steps are supplied as separate parts ready to be bolted together. Module supplied as a kit to be bolted together. > 1 - level the base. This is used as a template. Identify the sides on the sticker. Assemble the uprights, stringers and steps, but do not fully tighten the bolts. The base is used as a template for assembly. once the components have been bolted,...

Open the catalog to page 12

All MILLS catalogs and technical brochures

  1. FP075

    1 Pages

  2. TIROIR

    8 Pages

  3. Escalib Mills

    16 Pages

  4. Mills Tour

    28 Pages

  5. Tourechaf

    32 Pages