|
KNX 2007 - 283 Pages
Combi sensor
1
2
3
A
C
B1
B2
B3
D
Ref.-No.
Combi sensor WS 10 KS
– with DCF77 receiver WS 10 KSDCF
(No KNX device)
The combi sensor serves for the measurement of the wind speed, brightness dawn and rain.
The brightness can be measured for three directions, south, east and west, separately.
The combi sensor will be connected directly to the weather station (2224 REG W) which evaluates the measured data and transmits these as
switching or value telegrams to the bus.
The combi sensor WS 10 KSDCF includes an additional DCF77 receiver for the official German time signal.
The combi sensor needs an external 24 V AC supply, e.g. power supply WSSV 10.
126
4 Technical data
Supply: 24 V AC ± 15 %, 50/60 Hz
Max. current consumption: 600 mA
Power consumption: max. 14.4 W (sensors and heating)
Ambient temperature: –5°C ... +45°C
Connection cable: LiYCY, 6 x 0.25 mm, 10 m, max. 50 m
Ambient temperature: –40°C ... +60°C, ice free
Storage/transport temperature: –40°C ... +60°C
Protection: IP 55, in standard purpose acc. to DIN EN 60592
Safety class: III
Dimensions: 130 x 200 mm (without mounting bracket)
Fastening: mounting bracket for wall or mast
Sensor signals
Wind speed: 1 ... 40 m/s
Accuracy: 0.5 m/s, –20°C ... +60°C
Rain: Yes / No
Sensitivity: fine drizzle
Switch On delay: approx. 3 rain particles
Switch Off delay: approx. 2 minutes
Brightness
Range: 0 ... 110 KLux
Spectral range: 700 ... 1050 nm
Resolution: 10 bit
Direction: east, south, west
Dawn
Range: 0 ... 674 Lux
Resolution: 10 bit
A: Wind wheel
B1 ... B3: Brightness sensors
west, east, south
C: Dawn sensor
D: Rain sensor
-
P. 1
-
P. 123
121Weather station Ref.-No. 2224 REG W4 Technical dataMeasuring sensor power supply outputsNumber: 2Rated voltage: 24 V DC ±10 %Rated current: 100... -
P. 124
122Weather station Ref.-No. 2224 REG W45Remarks on the hardwarePlease observe the following basic rules when installing the analog input extension module:•... -
P. 125
Building orientationThe automatic shading control starts at the moment when at least one of the three brightness sensors indicates that the luminance has... -
P. 126
Analog InputExtension Module123(A)(C)(B)(D)(E)K1 K2 K3 K4+UsGNDKNX/EIBAC 230 V~50/60 Hz AC 24 VUs GND K1 K2 K3 K4 GND Us24V DCBereich:Linie:TLNNr.:24V... -
P. 127
Analog InputPower Supply123AC 230 V~50/60 Hz AC 24 V~AC 24 V~• AC 24 V • AC 24 VAC 230 V~L NLNRef.-No.Power supply WSSV 10(No KNX device)Series... -
P. 128
-
P. 129
Analog Sensors forWeather Station123Ref.-No.Wind sensor WS 10 W(No KNX device)The wind sensor converts the wind speed into electrical signals. These signals... -
P. 130
Analog Sensors forWeather Station123Ref.-No.Rain sensor WS 10 R(No KNX device)The rain sensor is used for the measuring and evaluation of the rainfall.With... -
P. 131
129123Ref.-No.Brightness sensor WS 10 H(No KNX device)The brightness sensor is used for the measuring and evaluation of the brightness.The brightness measured... -
P. 132
Weather station Ref.-No. WS 10 ..130123Ref.-No.Temperature sensor WS 10 T(No KNX device)The temperature sensor is used for the measuring and evaluation... -
P. 133
Analog output4-gang123Ref.-No.KNX analog output 2204.01 REGAETS-product family: OutputProduct type: 4-gang analog outputSeries embodiment (SE)-device (4... -
P. 140
-
P. 150
-
P. 160
-
P. 170
-
P. 180
-
P. 190
-
P. 200
