|
KNX 2007 - 283 Pages
Analog Input
Power Supply
1
2
3
AC 230 V~
50/60 Hz AC 24 V~
AC 24 V~
• AC 24 V • AC 24 V
AC 230 V~
L N
L
N
Ref.-No.
Power supply WSSV 10
(No KNX device)
Series embodiment (SE)-device (4 units)
The power supply AC 24 V serves for the supply of KNX devices as e.g. Weather station 2224 REG W, Analog input 2214 REG A or analog input
extension module 2214 REG AM.
Above that, also the sensors as e.g. WS 10 W, WS 10 R or the Combi sensor WS 10 KS and their internal heating can be supplied as far as the
max. output current of the power supply is not exceeded.
The power supply is protected against overload and short-circuits by a thermo-switch.
Automatic restart after cool down or elimination of the short circuit.
125
4 Technical data
Net voltage: 230 V AC ± 10 %, 50/60 Hz
Output voltage: 24 V AC ± 10 %, 50/60 Hz
Output current: max. 1 A
Power-on time: 100 %
Short-circuit protection: Thermo switch
Ambient temperature: –5°C ... +40°C, ice free
Storage/transport temperature: –25°C ... +70°C
Protection: IP 20
Connection: Screw terminals: 0.34 mm2 to 4 mm2, fine-wire (without ferrule)
0.14 mm2 to 2.5 mm2, fine-wire (incl. ferrule)
-
P. 1
-
P. 122
120Weather station Ref.-No. 2224 REG W4 Technical dataKNX SupplyVoltage: 21 – 32 V DC (SELV)Power consumption: typically 150 mWConnection: Bus terminal... -
P. 123
121Weather station Ref.-No. 2224 REG W4 Technical dataMeasuring sensor power supply outputsNumber: 2Rated voltage: 24 V DC ±10 %Rated current: 100... -
P. 124
122Weather station Ref.-No. 2224 REG W45Remarks on the hardwarePlease observe the following basic rules when installing the analog input extension module:•... -
P. 125
Building orientationThe automatic shading control starts at the moment when at least one of the three brightness sensors indicates that the luminance has... -
P. 126
Analog InputExtension Module123(A)(C)(B)(D)(E)K1 K2 K3 K4+UsGNDKNX/EIBAC 230 V~50/60 Hz AC 24 VUs GND K1 K2 K3 K4 GND Us24V DCBereich:Linie:TLNNr.:24V... -
P. 127
-
P. 128
Combi sensor123ACB1B2B3DRef.-No.Combi sensor WS 10 KS– with DCF77 receiver WS 10 KSDCF(No KNX device)The combi sensor serves for the measurement... -
P. 129
Analog Sensors forWeather Station123Ref.-No.Wind sensor WS 10 W(No KNX device)The wind sensor converts the wind speed into electrical signals. These signals... -
P. 130
Analog Sensors forWeather Station123Ref.-No.Rain sensor WS 10 R(No KNX device)The rain sensor is used for the measuring and evaluation of the rainfall.With... -
P. 131
129123Ref.-No.Brightness sensor WS 10 H(No KNX device)The brightness sensor is used for the measuring and evaluation of the brightness.The brightness measured... -
P. 132
Weather station Ref.-No. WS 10 ..130123Ref.-No.Temperature sensor WS 10 T(No KNX device)The temperature sensor is used for the measuring and evaluation... -
P. 140
-
P. 150
-
P. 160
-
P. 170
-
P. 180
-
P. 190
-
P. 200
